Infiniti I30 (A33). Manual — part 458
SEL550X
6.
Select “Heading up” or “North up” icon.
I
To display North up, select “North up”.
I
To display the car heading up, select “Heading up”.
7.
Push “MAP” switch, then the display will go back to the current
location map.
SEL551X
“NEARBY DISPLAY ICONS” MODE
NHEL0301S10
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Nearby Display Icons”.
SEL552X
6.
Select and touch an item on the list.
7.
Push “MAP” switch, then the display will go back to the current
location map.
SEL553X
“ADJUST CURRENT LOCATION” MODE
NHEL0301S11
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Adjust Current Location”.
SEL554X
6.
Select “
” or “
” to calibrate the heading direction. (Arrow
marks will rotate corresponding to the calibration key.)
7.
Select “Set”. Then the vehicle mark will be matched to the
arrow mark.
8.
Display will show “Heading direction has been calibrated” and
then go back to the current location map.
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
NAVIGATION SYSTEM
Control Panel Mode (Cont’d)
EL-501
SEL555X
“BEEP ON/OFF” MODE
NHEL0301S12
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Touch “Beep On/Off”.
SEL556X
6.
Select “On” or “Off” icon.
I
If you want the beep sound, select “On”.
I
If you do not want the beep sound, select “Off”.
7.
Push “PREVIOUS” switch, then the display will go back to the
current location map.
SEL641X
“CLEAR MEMORY” MODE
NHEL0301S13
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Select “System Setting”.
5.
Select “Clear Memory”.
SEL558X
6.
To delete all the stored places in “Address Book”, “Avoid Area”
and “Previous Dest”, select “Yes”.
NAVIGATION SYSTEM
Control Panel Mode (Cont’d)
EL-502
Guide Volume Setting
=NHEL0302
DESCRIPTION
NHEL0302S01
Following voice guidance setting can be changed.
I
Voice guidance activation/deactivation
I
Voice volume of the guidance
SEL563X
ACTIVATION/DEACTIVATION SETTING
NHEL0302S02
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
The voice prompt can be turned on/off by pressing the “Guid-
ance Volume” button.
SEL563X
VOICE VOLUME SETTING
NHEL0302S03
1.
Start the engine.
2.
Push “OPEN/CLOSE” switch and then open the display.
3.
Push “SETTING” switch.
4.
Volume of the voice can be controlled by bending the joystick
to left/right.
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
NAVIGATION SYSTEM
Guide Volume Setting
EL-503
Trouble Diagnoses
=NHEL0303
SYMPTOM CHART
NHEL0303S01
Symptom
Diagnoses/service procedure
Reference
page
Any function of the system
does not operate.
Check power supply and ground circuit for NAVI control unit.
Strange screen color or
unusual screen brightness.
1. Check “DISPLAY SETTING” MODE.
2. Check display in “DIAGNOSE THE DISPLAY” MODE.
The display is not dimmed
when turning lighting switch
to ON.
1. Check “DISPLAY SETTING” MODE.
2. Check lighting switch signal input to NAVI control unit correctly in “DIAGNOSIS
FOR THE SIGNALS FROM THE CAR” MODE.
No navigation guide voice
are heard from both front
speakers.
1. Check “Guide Volume Setting”.
2. Check voice guide operation.
Beep does not sound when
the system guides route.
Check “BEEP ON/OFF” MODE.
Position marker does not
trace along the route being
traveled.
Go to “WORK FLOW FOR NAVIGATION INSPECTION”.
Position marker does not
indicate forward or backward
movement.
Check reverse signal input to NAVI control unit correctly by “DIAGNOSIS FOR
THE SIGNALS FROM THE CAR” MODE.
Radio wave of GPS cannot
be received. (GPS marker
on the display does not
become green color.)
1. Is there anything obstructing the GPS antenna on the rear parcel finisher?
(GPS antenna located under the rear parcel finisher.)
—
2. Check GPS radio wave receive condition in “GPS INFORMATION MODE”.
3. Check GPS antenna in “Self Diagnosis”.
Heading direction of position
marker does not match
vehicle direction.
1. Perform “ADJUST CURRENT LOCATION” MODE.
2. Go to “WORK FLOW FOR NAVIGATION INSPECTION”.
Stored location in the
address book and other
memory functions are lost
when battery is disconnected
or becomes discharged.
Stored location in the address book and other memory functions may be lost if the
battery is disconnected or becomes discharged. If this should occur, charge or
replace the battery as necessary and re-enter the information.
—
Map appears grey and can-
not be scrolled
The current location in the memory is out of the map data area.
Perform “INITIALIZE LOCATION” MODE.
NAVIGATION SYSTEM
Trouble Diagnoses
EL-504
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст