Infiniti I30 (A33). Manual — part 424
Remote Controller Battery Replacement
NHEL0118
SEL366W
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
MULTI-REMOTE CONTROL SYSTEM
Remote Controller Battery Replacement
EL-365
Component Parts and Harness Connector
Location
NHEL0119
SEL055Y
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Component Parts and Harness Connector Location
EL-366
System Description
NHEL0196
DESCRIPTION
NHEL0196S01
1. Operation Flow
NHEL0196S0101
SEL334W
2. Setting The Vehicle Security System
NHEL0196S0102
Initial condition
1) Ignition switch is in OFF position.
Disarmed phase
When the vehicle security system is in the disarmed phase, the security indicator lamp blinks every 2.6 sec-
onds.
Pre-armed phase and armed phase
When the following operation 1) or 2) is performed, the vehicle security system turns into the “pre-armed”
phase. (The security indicator lamp illuminates.)
1) Smart entrance control unit receives LOCK signal from key cylinder switch or multi-remote controller after
hood, trunk lid and all doors are closed.
2) Hood, trunk lid and all doors are closed after front doors are locked by key, lock/unlock switch or multi-
remote controller.
After about 30 seconds, the system automatically shifts into the “armed” phase (the system is set). (The
security indicator lamp blinks every 2.6 seconds.)
3. Canceling The Set Vehicle Security System
NHEL0196S0103
When the following 1) or 2) operation is performed, the armed phase is canceled.
1) Unlock the doors with the key or multi-remote controller.
2) Open the trunk lid with the key or multi-remote controller.
4. Activating The Alarm Operation of The Vehicle Security System
NHEL0196S0104
Make sure the system is in the armed phase. (The security indicator lamp blinks every 2.6 seconds.)
When the following operation 1) or 2) is performed, the system sounds the horns and flashes the headlamps
for about 50 seconds.
1) Engine hood, trunk lid or any door is opened during armed phase.
2) Disconnecting and connecting the battery connector before canceling armed phase.
POWER SUPPLY AND GROUND
NHEL0196S02
Power is supplied at all times
I
through 10A fuse [No. 12, located in the fuse block (J/B)]
I
to security indicator lamp terminal 1.
Power is supplied at all times
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
VEHICLE SECURITY (THEFT WARNING) SYSTEM
System Description
EL-367
I
through 10A fuse [No. 13, located in the fuse block (J/B)]
I
to smart entrance control unit terminal 49.
With the ignition switch in the ON or START position, power is supplied
I
through 10A fuse [No. 10, located in the fuse block (J/B)]
I
to smart entrance control unit terminal 27.
With the ignition switch in the ACC or ON position, power is supplied
I
through 10A fuse [No. 1, located in the fuse block (J/B)]
I
to smart entrance control unit terminal 26.
Ground is supplied
I
to smart entrance control unit terminals 43 and 64
I
through body grounds M9, M25 and M87.
INITIAL CONDITION TO ACTIVATE THE SYSTEM
NHEL0196S03
The operation of the vehicle security system is controlled by the doors, hood and trunk lid.
Pattern A
NHEL0196S0301
To activate the vehicle security system, the smart entrance control unit must receive signals indicating the
doors, hood and trunk lid are closed.
When a door is open, smart entrance control unit terminal 1, 2 or 3 receives a ground signal from each door
switch.
When the hood is open, smart entrance control unit terminal 6 receives a ground signal
I
from terminal 1 of the hood switch
I
through body grounds E11, E22 and E53.
When the trunk lid is open, smart entrance control unit terminal 13 receives a ground signal
I
from terminal 1 of the trunk room lamp switch
I
through body grounds T6 and T8.
When smart entrance control unit receives LOCK signal from key cylinder switch or multi-remote controller and
none of the described conditions exist, the vehicle security system will automatically shift to armed mode.
Pattern B
NHEL0196S0302
To activate the vehicle security system, the smart entrance control unit must receive signal indicating any door
(including hood and trunk lid) is opened.
When the front doors are locked with key, lock/unlock switch or multi-remote controller and then all doors are
closed, the vehicle security system will automatically shift to armed mode.
VEHICLE SECURITY SYSTEM ACTIVATION
NHEL0196S04
Pattern A
NHEL0196S0401
With all doors (including hood and trunk lid) close if the key is used to lock doors, terminal 11 receives a ground
signal
I
from terminal 5 (with IVCS) or 3 (without IVCS) of the key cylinder switch LH
I
through body grounds M9, M25 and M87.
If this signal, or lock signal from remote controller is received by the smart entrance control unit, the vehicle
security system will activate automatically.
NOTE:
Vehicle security system can be set even though all doors are not locked.
Pattern B
NHEL0196S0402
With any door (including hood and trunk lid) open if lock/unlock switch is used to lock doors, terminal 5 receives
a ground signal
I
from terminal 6 of lock/unlock switch LH, or
I
from terminal 8 of lock/unlock switch RH
I
through body grounds M9, M25 and M87, or
With any door (including hood and trunk lid) open if the key is used to lock doors, terminal 11 receives a ground
signal
I
from terminal 5 (with IVCS) or 3 (without IVCS) of the key cylinder switch LH
I
through body grounds M9, M25 and M87.
VEHICLE SECURITY (THEFT WARNING) SYSTEM
System Description (Cont’d)
EL-368
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст