Infiniti I30 (A33). Manual — part 537
HFC-134a (R-134a) Service Procedure
NHHA0228
SETTING OF SERVICE TOOLS AND EQUIPMENT
NHHA0228S01
Discharging Refrigerant
NHHA0228S0101
WARNING:
Avoid breathing A/C refrigerant and lubricant vapor or mist. Exposure may irritate eyes, nose and
throat. Remove HFC-134a (R-134a) from A/C system using certified service equipment meeting require-
ments of SAE J2210 (R-134a recycling equipment) or J2209 (R-134a recovery equipment). If acciden-
tal system discharge occurs, ventilate work area before resuming service. Additional health and safety
information may be obtained from refrigerant and lubricant manufacturers.
SHA179FD
Evacuating System and Charging Refrigerant
NHHA0228S0102
SHA180FD
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
SC
EL
IDX
SERVICE PROCEDURE
HFC-134a (R-134a) Service Procedure
HA-107
Maintenance of Lubricant Quantity in
Compressor
NHHA0229
The lubricant in the compressor circulates through the system with
the refrigerant. Add lubricant to compressor when replacing any
component or after a large gas leakage occurred. It is important to
maintain the specified amount. If lubricant quantity is not main-
tained properly, the following malfunctions may result:
I
Lack of lubricant: May lead to a seized compressor
I
Excessive lubricant: Inadequate cooling (thermal exchange
interference)
LUBRICANT
NHHA0229S01
Name: Nissan A/C System Oil Type S
Part number: KLH00-PAGS0
CHECKING AND ADJUSTING
NHHA0229S02
Adjust the lubricant quantity according to the test group shown
below.
1
CHECK LUBRICANT RETURN OPERATION
Can lubricant return operation be performed?
I
A/C system works properly.
I
There is no evidence of a large amount of lubricant leakage.
Yes or No
Yes
©
GO TO 2.
No
©
GO TO 3.
2
PERFORM LUBRICANT RETURN OPERATION, PROCEEDING AS FOLLOWS:
1. Start engine, and set the following conditions:
Test condition
Engine speed: Idling to 1,200 rpm
A/C or AUTO switch: ON
Blower speed: Max. position
Temp. control: Optional [Set so that intake air temperature is 25 to 30°C (77 to 86°F).]
2. Next item is for V-6 compressor. Connect the manifold gauge, and check that the high pressure side pressure
is 588 kPa (6 kg/cm
2
, 85 psi) or higher.
If less than the reference level, attach a cover to the front face of the condenser to raise the pressure.
3. Perform lubricant return operation for about 10 minutes.
4. Stop engine.
CAUTION:
If excessive lubricant leakage is noted, do not perform the lubricant return operation.
OK
©
GO TO 3.
3
CHECK COMPRESSOR
Should the compressor be replaced?
Yes or No
Yes
©
Go to “Lubricant Adjustment Procedure for Compressor Replacement”, (HA-110).
No
©
GO TO 4.
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
SC
EL
IDX
SERVICE PROCEDURE
Maintenance of Lubricant Quantity in Compressor
HA-109
4
CHECK ANY PART
Is there any part to be replaced? (Evaporator, condenser, liquid tank or in case there is evidence of a large amount of
lubricant leakage.)
Yes or No
Yes
©
Go to “Lubricant Adjusting Procedure for Components Replacement Except
Compressor”, (HA-110).
No
©
Carry out the A/C performance test.
Lubricant Adjusting Procedure for Components
Replacement Except Compressor
NHHA0229S0201
After replacing any of the following major components, add the
correct amount of lubricant to the system.
Amount of lubricant to be added
Part replaced
Lubricant to be added to
system
Remarks
Amount of lubricant
m
(US fl oz, Imp fl oz)
Evaporator
75 (2.5, 2.6)
—
Condenser
75 (2.5, 2.6)
—
Liquid tank
5 (0.2, 0.2)
Add if compressor is not
replaced. *1
In case of refrigerant
leak
30 (1.0, 1.1)
Large leak
—
Small leak *2
*1:
If compressor is replaced, addition of lubricant is included in the table.
*2:
If refrigerant leak is small, no addition of lubricant is needed.
Lubricant Adjusting Procedure for Compressor
Replacement
NHHA0229S0202
1.
Before connecting ACR4 to vehicle, check ACR4 gauges. No
refrigerant pressure should be displayed. If NG, recover refrig-
erant from equipment lines.
2.
Connect ACR4 to vehicle. Confirm refrigerant purity in supply
tank using ACR4 and refrigerant identifier. If NG, refer to
“CONTAMINATED REFRIGERANT”, HA-2.
3.
Confirm refrigerant purity in vehicle A/C system using ACR4
and refrigerant identifier. If NG, refer to “CONTAMINATED
REFRIGERANT”, HA-2.
4.
Discharge refrigerant into the refrigerant recovery/recycling
equipment. Measure lubricant discharged into the recovery/
recycling equipment.
5.
Remove the drain plug of the “old” (removed) compressor.
Drain the lubricant into a graduated container and record the
amount of drained lubricant.
6.
Remove the drain plug and drain the lubricant from the “new”
compressor into a separate, clean container.
7.
Measure an amount of new lubricant installed equal to amount
drained from “old” compressor. Add this lubricant to “new” com-
pressor through the suction port opening.
8.
Measure an amount of new lubricant equal to the amount
recovered during discharging. Add this lubricant to “new” com-
pressor through the suction port opening.
9.
Torque the drain plug.
18 - 19 N·m (1.8 - 1.9 kg-m, 13 - 14 ft-lb)
SERVICE PROCEDURE
Maintenance of Lubricant Quantity in Compressor (Cont’d)
HA-110
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст