Infiniti I30 (A33). Manual — part 224
Possible Cause
NHEC0434
I
Heated oxygen sensor 1 (front)
I
Fuel pressure
I
Injectors
I
Heated oxygen sensor 1 heater (front)
DTC Confirmation Procedure
NHEC0105
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously conducted,
always turn ignition switch “OFF” and wait at least 10 seconds
before conducting the next test.
TESTING CONDITION:
I
Always perform at a temperature above −10°C (14°F).
I
Before performing the following procedure, confirm that
battery voltage is more than 11V at idle.
SEF653Y
SEF654Y
SEF655Y
WITH CONSULT-II
NHEC0105S01
1)
Start engine and warm it up to normal operating temperature.
2)
Stop engine and wait at least 5 seconds.
3)
Turn ignition switch “ON” and select “HO2S1 (B1) P0132” or
“HO2S1 (B2) P0152” of “HO2S1” in “DTC WORK SUPPORT”
mode with CONSULT-II.
4)
Touch “START”.
5)
Start engine and let it idle for at least 3 minutes.
NOTE:
Never raise engine speed above 3,600 rpm after this step. If
the engine speed limit is exceeded, return to step 5.
6)
When the following conditions are met, “TESTING” will be dis-
played on the CONSULT-II screen. Maintain the conditions
continuously until “TESTING” changes to “COMPLETED”. (It
will take approximately 50 seconds or more.)
ENG SPEED
1,200 - 2,600 rpm
Vehicle speed
80 - 100 km/h (50 - 62 MPH)
B/FUEL SCHDL
3 - 9 msec
Selector lever
Suitable position
If “TESTING” is not displayed after 5 minutes, retry from
step 2.
7)
Make sure that “OK” is displayed after touching “SELF-DIAG
RESULTS”.
If
“NG”
is
displayed,
refer
to
“Diagnostic
Procedure”, EC-212.
GI
MA
EM
LC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0132 (BANK 1), P0152 (BANK 2) HO2S1 (FRONT) (RICH SHIFT
MONITORING)
Possible Cause
EC-211
SEF308XB
Overall Function Check
NHEC0106
Use this procedure to check the overall function of the heated oxy-
gen sensor 1 (front) circuit. During this check, a 1st trip DTC might
not be confirmed.
WITH GST
NHEC0106S01
1)
Start engine and warm it up to normal operating temperature.
2)
Set voltmeter probes between ECM terminal 63 [HO2S1 (B1)
signal] or 62 [HO2S1 (B2) signal] and engine ground.
3)
Check one of the following with engine speed held at 2,000
rpm constant under no load.
I
The maximum voltage is below 0.8V at least one time.
I
The minimum voltage is below 0.35V at least one time.
4)
If NG, go to “Diagnostic Procedure”, EC-212.
Diagnostic Procedure
NHEC0107
1
RETIGHTEN GROUND SCREWS
1. Turn ignition switch “OFF”.
2. Loosen and retighten engine ground screws.
SEF255X
©
GO TO 2.
2
RETIGHTEN HEATED OXYGEN SENSOR 1 (FRONT)
Loosen and retighten corresponding heated oxygen sensor 1 (front).
Tightening torque:
40 - 60 N·m (4.1 - 6.2 kg-m, 30 - 44 ft-lb)
©
GO TO 3.
DTC P0132 (BANK 1), P0152 (BANK 2) HO2S1 (FRONT) (RICH SHIFT
MONITORING)
Overall Function Check
EC-212
3
CLEAR THE SELF-LEARNING DATA
With CONSULT-II
1. Start engine and warm it up to normal operating temperature.
2. Select “SELF-LEARNING CONT” in “WORK SUPPORT” mode with CONSULT-II.
3. Clear the self-learning control coefficient by touching “START”.
SEF215Z
4. Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0172 or P0175 detected?
Is it difficult to start engine?
Without CONSULT-II
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch “OFF”.
3. Disconnect mass air flow sensor harness connector, and restart and run engine for at least 5 seconds at idle speed.
4. Stop engine and reconnect mass air flow sensor harness connector.
5. Make sure 1st trip DTC P0100 is displayed.
6. Erase the 1st trip DTC memory. Refer to “HOW TO ERASE EMISSION-RELATED DIAGNOSTIC INFORMATION”,
7. Make sure DTC P0000 is displayed.
8. Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0172 or P0175 detected?
Is it difficult to start engine?
Yes or No
Yes
©
Perform trouble diagnosis for DTC P0172, P0175. Refer to EC-300.
No
©
GO TO 4.
4
CHECK HO2S1 (FRONT) CONNECTOR FOR WATER
1. Turn ignition switch “OFF”.
2. Check heated oxygen sensor 1 (front) harness protector color.
SEC020C
3. Disconnect heated oxygen sensor 1 (front) harness connector.
4. Check connectors for water.
Water should not exist.
OK or NG
OK
©
GO TO 5.
NG
©
Repair or replace harness or connectors.
GI
MA
EM
LC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0132 (BANK 1), P0152 (BANK 2) HO2S1 (FRONT) (RICH SHIFT
MONITORING)
Diagnostic Procedure (Cont’d)
EC-213
5
CHECK HEATED OXYGEN SENSOR 1 HEATER (FRONT)
Check resistance between HO2S1 (front) terminals as follows.
SEF310X
CAUTION:
Discard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
OK or NG
OK (With CONSULT-II)
©
GO TO 6.
OK (Without CONSULT-
II)
©
GO TO 7.
NG
©
GO TO 8.
DTC P0132 (BANK 1), P0152 (BANK 2) HO2S1 (FRONT) (RICH SHIFT
MONITORING)
Diagnostic Procedure (Cont’d)
EC-214
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст