Infiniti QX56 (JA60). Manual — part 312
TRANSFER ASSEMBLY
DLN-171
< DISASSEMBLY AND ASSEMBLY >
[ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
39. Remove all the sealant from the switch location area and inside
the center case.
CAUTION:
Remove old sealant adhering to mounting surfaces. Also
remove any moisture, oil, or foreign material adhering to
application and mounting surfaces.
40. Thread the ATP switch and neutral-4LO switch in one to two
pitches and apply sealant to the threads of the switches. Tighten
to the specified torque. Refer to
• Use Genuine Silicone RTV or equivalent. Refer to
"Recommended Chemical Products and Sealants"
.
NOTE:
• Neutral-4LO switch harness connector is gray.
• ATP switch harness connector is black.
41. Install the front drive shaft rear bearing using Tools.
42. Install the front drive shaft to the front bearing using Tools.
43. Install the drive chain to the front drive shaft and clutch drum.
CAUTION:
Install drive chain by aligning identification marks to the
rear as shown.
Tool number
A: KV40100621 (J-25273)
B: ST30032000 (J-26010-01)
SDIA3435E
SDIA2198E
Tool number
A: KV40100621 (J-25273)
B: ST30032000 (J-26010-01)
SDIA2199E
SDIA2200E
DLN-172
< DISASSEMBLY AND ASSEMBLY >
[ATX14B]
TRANSFER ASSEMBLY
44. Tap the front drive shaft while keeping it upright and press-fit the
front drive shaft rear bearing.
CAUTION:
Do not tap drive chain.
45. Install the front case assembly. Refer to
.
46. Install the rear case assembly. Refer to
.
Front Case
1. Install the carrier bearing to the sun gear using Tools.
2. Install the new snap ring to the sun gear assembly using suitable
tool.
CAUTION:
Do not reuse snap ring.
3. Apply ATF to the circumference of the new metal bushing and
install it to the sun gear assembly using Tool.
CAUTION:
• Do not reuse metal bushing.
• Apply ATF to metal bushing before installing.
4. Apply ATF to the new needle bearing and install it to the sun
gear assembly using Tool.
CAUTION:
• Do not reuse needle bearing.
• Apply ATF to needle bearing before installing.
SMT988C
Tool number
A: ST30911000 ( — )
B: KV31103300 ( — )
SDIA2179E
SDIA2148E
Tool number
: ST35300000 ( — )
Dimension A
: 7.7 - 8.3 mm (0.303 - 0.327 in)
SDIA3189E
Tool number
: ST33220000 ( — )
Dimension B
: 62.5 - 63.1 mm (2.461 - 2.484 in)
SDIA3190E
TRANSFER ASSEMBLY
DLN-173
< DISASSEMBLY AND ASSEMBLY >
[ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
5. Install the sun gear assembly to the planetary carrier assembly.
6. Install the new snap ring to the planetary carrier assembly.
CAUTION:
Do not reuse snap ring.
7. Set the input bearing into the front case and install using Tool.
8. Install the new snap ring into the front case.
CAUTION:
Do not reuse snap ring.
9. Install the internal gear with its groove facing the snap ring into
the front case. Then secure it with the new snap ring.
CAUTION:
Do not reuse snap ring.
SDIA2180E
SDIA2794E
Tool number
: ST30720000 (J-25405)
SDIA2172E
SDIA2171E
WDIA0100E
DLN-174
< DISASSEMBLY AND ASSEMBLY >
[ATX14B]
TRANSFER ASSEMBLY
10. Install the new front oil seal until it is seated flush with the end
face of the front case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal lip before installing.
11. Install the planetary carrier assembly and sun gear assembly to
the front case using Tool.
12. Install the new snap ring to the sun gear.
CAUTION:
Do not reuse snap ring.
13. Apply petroleum jelly to the circumference of the new oil seal,
and install it to the front case using Tools.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
14. Install the fork guide, shift fork spring, 2-4 fork, and L-H fork to
the shift rod, and secure them with new retaining pins.
CAUTION:
Do not reuse retaining pins.
Tool number
: KV38100500 ( — )
SDIA3383E
Tool number
: ST33200000 (J-26082)
SDIA2791E
SDIA2144E
Tool number
A: ST30720000 (J-25405)
B: ST33200000 (J-26082)
Dimension
: 4.0 - 4.6 mm (0.157 - 0.181 mm)
SDIA3191E
SDIA2142E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст