Infiniti QX56 (JA60). Manual — part 311
TRANSFER ASSEMBLY
DLN-167
< DISASSEMBLY AND ASSEMBLY >
[ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Use Genuine Silicone RTV or equivalent. Refer to
GI-15, "Recommended Chemical Products and
.
CAUTION:
Do not reuse oil pressure check plug.
20. Install the new snap ring to the clutch hub using suitable tool.
CAUTION:
Do not reuse snap ring.
21. Apply petroleum jelly to the needle bearing, and install the nee-
dle bearing, spacer, clutch drum and clutch hub to the main-
shaft.
22. Install the new snap ring to the mainshaft.
CAUTION:
Do not reuse snap rings.
23. Apply ATF each plate, then install them into the clutch drum as
shown.
WDIA0101E
WDIA0129E
SDIA2192E
SDIA2193E
DLN-168
< DISASSEMBLY AND ASSEMBLY >
[ATX14B]
TRANSFER ASSEMBLY
24. Install the return spring assembly into the clutch hub.
25. Install the press flange by aligning the notches to the clutch hub
as shown.
26. Press the press flange to install the new snap ring into snap ring
groove on mainshaft using Tools.
CAUTION:
Do not reuse snap ring.
27. Install the new snap ring to the mainshaft using suitable tool.
CAUTION:
Do not reuse snap ring.
28. Apply ATF to the thrust needle bearing and install it on the press
flange.
SMT911C
SDIA2194E
Tool number
A: ST22452000 (J-34335)
B: ST30911000 ( — )
C: KV31103300 ( — )
SDIA2111E
SDIA2112E
SDIA2109E
TRANSFER ASSEMBLY
DLN-169
< DISASSEMBLY AND ASSEMBLY >
[ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
29. Install the new snap ring to the main shaft.
CAUTION:
Do not reuse snap ring.
30. Install the mainshaft rear bearing to the center case using Tool.
31. Install the mainshaft assembly using a press.
• Press the mainshaft into the center case using Tools.
32. Install the C-rings to the mainshaft.
33. Set the washer holder on the mainshaft, and secure it with a
new snap ring.
CAUTION:
Do not reuse snap ring.
SDIA2195E
Tool number
: ST15310000 (J-25640-B)
SDIA2196E
Tool number
A: ST30911000 ( — )
B: ST33052000 ( — )
SDIA2197E
SDIA2201E
SDIA2104E
DLN-170
< DISASSEMBLY AND ASSEMBLY >
[ATX14B]
TRANSFER ASSEMBLY
34. Apply petroleum jelly to the stem bleeder and install it to the cen-
ter case.
35. Apply ATF to the new seal ring and install it to the main oil pump
cover.
CAUTION:
Do not reuse seal ring.
36. Install the inner gear and outer gear in the main oil pump hous-
ing. Then, measure the side clearance. Refer to
.
37. Install the main oil pump housing, outer gear and inner gear to
the center case.
38. Install the main oil pump cover to the center case, and tighten to
the specified torque. Refer to
SDIA2780E
SDIA2783E
SDIA2174E
SDIA2188E
SDIA2130E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст