Infiniti G35 (V35). Manual — part 720
SC-16
STARTING SYSTEM
WORK FLOW
SKIB1369E
*1
SC-6, "Trouble Diagnoses with Battery/
Starting/Charging System Tester (Bat-
tery)"
.
*2
SC-18, "MINIMUM SPECIFICATION
OF CRANKING VOLTAGE REFER-
ENCING COOLANT TEMPERATURE"
.
*3
SC-17, "Check “B” Terminal Circuit"
*4
SC-18, "Check “S” Connector Circuit"
.
STARTING SYSTEM
SC-17
C
D
E
F
G
H
I
J
L
M
A
B
SC
DIAGNOSTIC PROCEDURE 1
Check “B” Terminal Circuit
1.
CHECK POWER SUPPLY FOR STARTER MOTOR “B” TERMINAL
1.
Remove fuel pump fuse.
2.
Crank or start the engine (where possible) until the fuel pressure is released.
3.
Turn ignition switch OFF.
4.
Make sure that the starter motor “B” terminal E203 terminal 2 (B/R) connection is clean and tight.
5.
Check voltage between starter motor “B” terminal E203 terminal
2 (B/R) and ground using.
OK or NG
OK
>> GO TO 2.
NG
>> Check harness between battery and starter motor for
open circuit.
2.
CHECK BATTERY CABLE CONNECTION (VOLTAGE DROP TEST)
Check voltage between starter motor “B” terminal E203 terminal 2
(B/R) and battery positive terminal.
OK or NG
OK
>> GO TO 3.
NG
>> Check harness between battery and starter motor for
poor continuity.
3.
CHECK STARTER MOTOR GROUND CIRCUIT (VOLTAGE DROP TEST)
1.
Turn ignition switch OFF.
2.
Check voltage between starter motor case and battery negative
terminal using.
OK or NG
OK
>> “B” terminal circuit is OK. Further inspection necessary.
Refer to
.
NG
>> Check starter motor case and ground for poor continuity.
2 (B/R) – Ground
: Battery voltage
PKIA2842E
2 (B/R) – Ground
When the ignition switch is in
START position
: Less than 0.5 V
PKIA2370E
Starter motor case – Battery negative terminal
When the ignition switch is in
START position
: Less than 0.2 V
PKIA2943E
SC-18
STARTING SYSTEM
DIAGNOSTIC PROCEDURE 2
Check “S” Connector Circuit
1.
CHECK POWER SUPPLY FOR STARTER MOTOR “S” TERMINAL
1.
Remove fuel pump fuse.
2.
Crank or start the engine (where possible) until the fuel pressure is released.
3.
Turn ignition switch OFF.
4.
Disconnect starter motors connector.
5.
Check voltage between starter motor connector F9 terminal 1
(B/Y) and ground.
OK or NG
OK
>> “S” connector circuit is OK. Further inspection neces-
NG
>> Check the following.
●
40A fusible link (letter M, located in fuse and fusible
link block)
●
Ignition switch
●
Starter relay (within the IPDM E/R)
●
Harness between starter motor and IPDM E/R
MINIMUM SPECIFICATION OF CRANKING VOLTAGE REFERENCING COOLANT TEMPERA-
TURE
1 (B/Y) – Ground
When the ignition switch
is in START position
: Battery voltage
PKIA2807E
Engine coolant temperature
Voltage [V]
−
30
°
C to
−
20
°
C (
−
22
°
F to
−
4
°
F)
8.4
−
19
°
C to
−
10
°
C (
−
2
°
F to 14
°
F)
8.9
−
9
°
C to 0
°
C (16
°
F to 32
°
F)
9.3
More than 1
°
C (More than 34
°
F)
9.7
STARTING SYSTEM
SC-19
C
D
E
F
G
H
I
J
L
M
A
B
SC
Removal and Installation
NKS000F0
REMOVAL
1.
Open the driver and front passenger window, and then disconnect the battery cable from the negative ter-
minal.
CAUTION:
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent
any interference between the window edge and the vehicle when the door is opened/closed. Dur-
ing normal operation, the window slightly raises and lowers automatically to prevent any window
to vehicle interference. The automatic window function will not work with the battery discon-
nected.
2.
Remove engine rear undercover, using power tools.
3.
Disconnect “S” connector.
4.
Remove “B” terminal nut.
5.
Remove starter motor mounting bolts and harness connector
clip bracket, using power tools.
6.
Remove starter motor downward.
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Be sure to tighten “B” terminal nut carefully.
1.
Starter motor mounting bolt
2.
Harness clip bracket
3.
S connector
4.
B terminal nut
5.
B terminal harness
6.
Starter motor
7.
Oil pan
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Engine front
PKIB8799E
PKIA2356E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст