Infiniti G35 (V35). Manual — part 158
RADIATOR CORE SUPPORT
BL-19
C
D
E
F
G
H
J
K
L
M
A
B
BL
RADIATOR CORE SUPPORT
PFP:62500
Removal and Installation
NIS000B0
REMOVAL
1.
Remove hood assembly. Refer to
BL-15, "Removal and Installation of Hood Assembly"
2.
Remove front bumper, bumper reinforcement and bumper bracket. Refer to
3.
Remove hood lock assembly, then remove hood lock cable.
4.
Remove washer tank. Refer to
WW-37, "Removal and Installation of Washer Tank"
5.
Remove horn connectors (High and Low).
6.
Remove the crash zone sensor. Refer to
SRS-49, "Removal and Installation"
.
7.
Disconnect the ambient sensor connector and remove the ambient sensor. Refer to
8.
Remove mounting harness clip on radiator core support assembly, the harness is separate.
9.
Remove resonator mounting screws. Refer to
EM-16, "AIR CLEANER AND AIR DUCT"
.
10. Remove air duct (LH/RH), and remove washer tank inlet clip.
11. Remove the mounting bolts, and remove bumper bracket (LH/RH).
1.
Hood stay
2.
Grommet
3.
Air intake duct (RH)
4.
Bumper bracket (RH)
5.
Radiator core support assembly
6.
Bumper bracket (LH)
7.
Air intake duct (LH)
8.
Horn (High)
9.
Horn (Low)
10. Hood rod clamp
11.
Upper radiator bracket
PIIA3546E
BL-20
RADIATOR CORE SUPPORT
12. Remove upper radiator bracket, and radiator core support
assembly mounting bolts. Remove mounting bolts with power
tool
CAUTION:
Put a wooden block under the radiator assembly to prevent the
radiator assembly from falling.
13. Remove headlamp (LH/RH). Refer to
14. Remove radiator core support assembly.
15. After removing radiator core support assembly, the following
parts are separate.
●
Remove the hood stay, grommet and hood rod clamp
●
Horn (High/Low)
●
Air intake duct (LH/RH)
INSTALLATION
Installation in the reverse order of removal.
SIIA1150E
POWER DOOR LOCK SYSTEM
BL-21
C
D
E
F
G
H
J
K
L
M
A
B
BL
POWER DOOR LOCK SYSTEM
PFP:24814
Component Parts and Harness Connector Location
NIS000B1
*: With Intelligent Key
PIIB7423E
BL-22
POWER DOOR LOCK SYSTEM
System Description
NIS000B2
Power is supplied at all times
●
to BCM terminal 55
●
through 50A fusible link (letter F , located in the fuse and fusible link box).
●
to BCM terminal 42
●
through 10A fuse [No. 18, located in the fuse block (J/B)].
●
to key switch terminal 2
●
through 10A fuse [No. 21, located in the fuse block (J/B)].(without Intelligent Key)
●
to key and ignition knob switch terminals 1 and 3
●
through 15A fuse [No. 33, located in the fuse and fusible link box].(with Intelligent Key)
Ground is supplied at all times
●
to BCM terminal 52
●
through grounds M30 and M66.
When key switch is ON (key is inserted in ignition key cylinder), power is supplied
●
to BCM terminal 37
●
through key switch terminal 1. (Without Intelligent Key)
●
through key switch and ignition knob switch terminal 4. (With Intelligent Key)
When the driver side door switch is ON (door is OPEN), ground is supplied
●
to BCM terminal 62
●
through driver side door switch terminal 1
●
through driver side door switch case ground.
When the passenger side door switch is ON (door is OPEN), ground is supplied
●
to BCM terminal 12
●
through passenger side door switch terminal 1
●
through passenger side door switch case ground.
When the door is locked or unlocked with power window main switch (door lock and unlock switch),
ground is supplied
●
to CPU of power window main switch
●
through power window main switch (door lock and unlock switch) terminal 15
●
through grounds M30 and M66.
Then power window main switch (door lock and unlock switch) operation signal is supplied
●
to BCM terminal 22
●
through power window main switch (door lock and unlock switch) terminal 12.
When the door is locked or unlocked with power window sub-switch (door lock and unlock switch),
ground is supplied
●
to CPU of power window sub-switch
●
through power window sub-switch (door lock and unlock switch) terminal 11
●
through grounds M30 and M66.
Then power window sub-switch (door lock and unlock switch) operation signal is supplied
●
to BCM terminal 22
●
through power window sub-switch (door lock and unlock switch) terminal 16.
When the door is locked with door key cylinder switch,
ground is supplied
●
to power window main switch (door lock and unlock switch) terminal 6
●
through door key cylinder switch terminals 1 and 5
●
through grounds M30 and M66.
Then door key cylinder switch operation signal is supplied
●
to BCM terminal 22
●
through power window main switch (door lock and unlock switch) terminal 12.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст