Infiniti G35 (V35). Manual — part 584
LT-16
HEADLAMP - XENON TYPE -
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check voltage between BCM harness connector and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
OK or NG
OK
>> INSPECTION END
NG
>> Repair harness or connector.
CONSULT-II Functions (BCM)
NKS002NN
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
CONSULT-II BASIC OPERATION
Refer to
GI-37, "CONSULT-II Start Procedure"
WORK SUPPORT
Operation Procedure
1.
Touch “HEAD LAMP” on “SELECT TEST ITEM” screen.
2.
Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3.
Touch “BATTERY SAVER SET” on “SELECT WORK ITEM” screen.
(+)
(
−
)
Ignition switch position
OFF
ACC
ON
BCM
connector
Terminal
M1
11
Ground
Approx. 0 V
Battery
voltage
Battery
voltage
38
Approx. 0 V
Approx. 0 V
Battery
voltage
M2
42
Battery
voltage
Battery
voltage
Battery
voltage
55
Battery
voltage
Battery
voltage
Battery
voltage
PKIA5204E
BCM
connector
Terminal
Ground
Continuity
M2
52
Yes
PKIA6256E
BCM diagnosis part
Diagnosis mode
Description
HEADLAMP
WORK SUPPORT
Changes the setting for each function.
DATA MONITOR
Displays BCM input data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending drive signal to them.
BCM
SELF-DIAG RESULTS
BCM performs self-diagnosis of CAN communication.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
HEADLAMP - XENON TYPE -
LT-17
C
D
E
F
G
H
I
J
L
M
A
B
LT
4.
Touch “START”.
5.
Touch “CHANGE SET”.
6.
The setting will be changed and “CUSTOMIZING COMPLETED” will be displayed.
7.
Touch “END”.
Display Item List
DATA MONITOR
Operation Procedure
1.
Touch “HEAD LAMP” on “SELECT TEST ITEM” screen.
2.
Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
3.
Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on “SELECT MONITOR ITEM” screen.
4.
When “SELECTION FROM MENU” is selected, touch individual items to be monitored. When “ALL SIG-
NALS” is selected, all the items will be monitored.
5.
Touch “START”.
6.
Touch “RECORD” while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch “STOP”.
Display Item List
Item
Description
BATTERY SAVER SET
Exterior lamp battery saver control mode can be changed in this mode. Selects exterior lamp bat-
tery saver control mode between two ON/OFF. Factory setting is ON.
CUSTOM A/LIGHT SETTING
Auto light sensitivity can be changed in this mode. Sensitivity can be adjusted in 4 modes. Fac-
tory setting is MODE 1.
●
MODE 1 (Normal)/MODE 2 (sensitive)/MODE 3 (Desensitized)/MODE 4 (Insensitive)
ILL DELAY SET
Auto light delay off timer period can be changed in this mode. Selects auto light delay off timer
period among eight modes. Factory setting is MODE 1.
●
MODE 1 (45 sec.)/MODE 2 (OFF)/MODE 3 (30 sec.)/MODE 4 (60 sec.)/MODE 5 (90 sec.)/
MODE 6 (120 sec.)/MODE 7 (150 sec.)/MODE 8 (180 sec.)
ALL SIGNALS
Monitors all the signals.
SELECTION FROM MENU
Selects items and monitor them.
Monitor item
Contents
IGN ON SW
“ON/OFF”
Displays status (ignition switch IGN position: ON/other: OFF) of ignition switch judged from
the ignition switch signal.
ACC ON SW
“ON/OFF”
Displays status (ignition switch ACC or IGN position: ON/other: OFF) of ignition switch
judged from the ignition switch signal.
HI BEAM SW
“ON/OFF”
Displays status (lighting switch high beam position: ON/other: OFF) of high beam switch
judged from the lighting switch signal.
HEAD LAMP SW 1
“ON/OFF”
Displays status (lighting switch 2ND position: ON/other: OFF) of headlamp 1 switch
judged from the lighting switch signal.
HEAD LAMP SW 2
“ON/OFF”
Displays status (lighting switch 2ND position: ON/other: OFF) of headlamp 2 switch
judged from the lighting switch signal.
LIGHT SW 1ST
“ON/OFF”
Displays status (lighting switch 1ST or 2ND position: ON/other: OFF) of lighting switch 1ST
position switch judged from the lighting switch signal.
AUTO LIGHT SW
NOTE 1
“ON/OFF”
Displays status (lighting switch AUTO position: ON/other: OFF) of auto light switch position
judged from the lighting switch signal.
PASSING SW
“ON/OFF”
Displays status (lighting switch passing position: ON/other: OFF) of passing switch judged
from the lighting switch signal.
FR FOG SW
“ON/OFF”
Displays status (lighting switch front fog lamp ON position: ON/others: OFF) of front fog
lamp switch judged from the lighting switch signal.
RR FOG SW
NOTE 2
“ON/OFF”
—
DOOR SW - DR
“ON/OFF”
Displays status (door is open: ON/door is closed: OFF) of driver side door switch judged
from the driver side door switch signal.
LT-18
HEADLAMP - XENON TYPE -
NOTE:
1. Vehicles without auto light system display this item, but cannot be monitored.
2. This item is displayed, but cannot be monitored.
3. Vehicles without daytime light system does not display this item.
ACTIVE TEST
Operation Procedure
1.
Touch “HEAD LAMP” on “SELECT TEST ITEM” screen.
2.
Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3.
Touch item to be tested and check operation of the selected item.
4.
During the operation check, touching “OFF” deactivates the operation.
Display Item List
NOTE:
1. Vehicles without daytime light lamp system does not display this item.
2. This item is displayed, but can not be tested.
CONSULT-II Functions (IPDM E/R)
NKS002NO
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
CONSULT-II BASIC OPERATION
Refer to
GI-37, "CONSULT-II Start Procedure"
DOOR SW - AS
“ON/OFF”
Displays status (door is open: ON/door is closed: OFF) of passenger side door switch
judged from the passenger side door switch signal.
DOOR SW - RR
NOTE 2
“OFF”
—
DOOR SW - RL
NOTE 2
“OFF”
—
BACK DOOR SW
NOTE 2
“OFF”
—
TURN SIGNAL R
“ON/OFF”
Displays status (turn signal switch right position: ON/other: OFF) of turn RH switch judged
from the turn signal switch signal.
TURN SIGNAL L
“ON/OFF”
Displays status (turn signal switch left position: ON/other: OFF) of turn LH switch judged
from the turn signal switch signal.
ENGINE RUN
NOTE 3
“ON/OFF”
Displays status (Engine running: ON/Other: OFF) as judged from engine status signal.
PKB SW
NOTE 3
“ON/OFF”
Displays status (Parking brake switch: ON/Other: OFF) of parking brake switch judged
from parking brake switch signal.
CARGO LAMP SW
NOTE 2
“OFF”
—
OPTICAL SENSOR
NOTE 1
“0 - 5 V”
Displays status “outside brightness (close to 5 V when light/close to 0 V when dark)” of
optical sensor judged from the optical sensor signal.
Monitor item
Contents
Test item
Description
TAIL LAMP
Allows tail lamp relay to operate by switching ON
−
OFF.
HEAD LAMP
Allows headlamp high relay and headlamp low relay to operate by switching ON
−
OFF.
FR FOG LAMP
Allows front fog lamp relay to operate by switching ON
−
OFF.
DTRL
NOTE1
Allows daytime light lamp operate by switching ON-OFF.
CORNERING LAMP
NOTE 2
—
Diagnosis Mode
Description
SELF-DIAGNOSTIC RESULTS
Refer to
.
DATA MONITOR
The input/output data of IPDM E/R is displayed in real time.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST
IPDM E/R sends a drive signal to electronic components to check their operation.
HEADLAMP - XENON TYPE -
LT-19
C
D
E
F
G
H
I
J
L
M
A
B
LT
DATA MONITOR
Operation Procedure
1.
Touch “DATA MONITOR” on “SELECT DIAG MODE ” screen.
2.
Touch “ALL SIGNALS”, “MAIN SIGNALS” or “SELECTION FROM MENU” on “SELECT MONITOR ITEM”
screen.
3.
When “SELECTION FROM MENU” is selected, touch individual items to be monitored. In “ALL SIG-
NALS”, all items are monitored. In “MAIN SIGNALS”, predetermined items are monitored.
4.
Touch “START”.
5.
Touch “RECORD” while monitoring to record the status of the item being monitored. To stop recording,
touch “STOP”.
All Signals, Main Signals, Selection From Menu
NOTE:
Perform monitoring of IPDM E/R data with ignition switch ON. When ignition switch is at ACC, display may not
be correct.
ACTIVE TEST
Operation Procedure
1.
Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
2.
Touch item to be tested, and check operation.
3.
Touch “START”.
4.
Touch “STOP” while testing to stop the operation.
ALL SIGNALS
Monitors all items.
MAIN SIGNALS
Monitor the predetermined item.
SELECTION FROM MENU
Selects items and monitors them.
Item name
CONSULT-II
screen display
Display
or unit
Monitor item selection
Description
ALL
SIGNALS
MAIN
SIGNALS
SELECTION
FROM MENU
Position lights request
TAIL&CLR REQ
ON/OFF
×
×
×
Signal status input from BCM
Headlamp low beam request
HL LO REQ
ON/OFF
×
×
×
Signal status input from BCM
Headlamp high beam request
HL HI REQ
ON/OFF
×
×
×
Signal status input from BCM
Front fog lights request
FR FOG REQ
ON/OFF
×
×
×
Signal status input from BCM
Test item
CONSULT-II
screen display
Description
Headlamp relay (HI, LO) output
LAMPS
Allows headlamp relay (HI, LO) to operate by switching operation (OFF, HI ON, LO
ON) at your option.
Front fog lamp relay output
Allows front fog lamp relay to operate by switching operation ON-OFF at your
option.
Tail lamp relay output
TAIL LAMP
Allows tail lamp relay to operate by switching operation ON-OFF at your option.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст