Infiniti G35 (V35). Manual — part 585
LT-20
HEADLAMP - XENON TYPE -
Headlamp Does Not Change To High Beam (Both Sides)
NKS002NP
1.
CHECK COMBINATION SWITCH INPUT SIGNAL
With CONSULT-II
Select “BCM” on CONSULT-II. With “HEAD LAMP” data monitor,
make sure “HI BEAM SW” turns ON-OFF linked with operation of
lighting switch.
Without CONSULT-II
Refer to
LT-100, "Combination Switch Inspection"
OK or NG
OK
>> GO TO 2.
NG
>> Check combination switch (lighting switch). Refer to
100, "Combination Switch Inspection"
.
2.
HEADLAMP ACTIVE TEST
With CONSULT-II
1.
Select “IPDM E/R” on CONSULT-II, and select “ACTIVE TEST”
on “SELECT DIAG MODE” screen.
2.
Select “LAMPS” on “SELECT TEST ITEM” screen.
3.
Touch “HI” screen.
4.
Make sure headlamp high beam operates.
Without CONSULT-II
1.
Start auto active test. Refer to
2.
Make sure headlamp high beam operates.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 4.
3.
CHECK IPDM E/R
1.
Select “IPDM E/R” on CONSULT-II, and select “DATA MONI-
TOR” on “SELECT DIAG MODE” screen.
2.
Make sure “HL LO REQ” and “HL HI REQ” turns ON when light-
ing switch is in HIGH BEAM position.
OK or NG
OK
NG
>> Replace BCM. Refer to
BCS-16, "Removal and Installa-
When lighting switch is
HIGH BEAM position
: HI BEAM SW ON
PKIA7585E
Headlamp high beam should operate.
(Headlamp high beam repeats ON
−
OFF every 1 second.)
Headlamp high beam should operate.
SKIA5774E
When lighting switch is
HIGH BEAM position
: HL LO REQ ON
: HL HI REQ ON
SKIA5775E
HEADLAMP - XENON TYPE -
LT-21
C
D
E
F
G
H
I
J
L
M
A
B
LT
4.
CHECK HEADLAMP INPUT SIGNAL
With CONSULT-II
1.
Turn ignition switch OFF.
2.
Disconnect front combination lamp RH and LH connectors.
3.
Select “IPDM E/R” on CONSULT-II, and select “ACTIVE TEST”
on “SELECT DIAG MODE” screen.
4.
Select “LAMPS” on “SELECT TEST ITEM” screen.
5.
Touch “HI” screen.
6.
When headlamp high relay is operating, check voltage between
front combination lamp harness connector and ground (head-
lamp high beam repeats ON
−
OFF every 1 second).
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Disconnect front combination lamp RH and LH connectors.
3.
Start auto active test. Refer to
.
4.
When headlamp high relay is operating, check voltage between front combination lamp harness connec-
tor and ground.
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 5.
5.
CHECK HEADLAMP CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector E7 ter-
minal 27 and front combination lamp RH harness connector E24
terminal 2.
4.
Check continuity between IPDM E/R harness connector E7 ter-
minal 28 and front combination lamp LH harness connector E41
terminal 2.
OK or NG
OK
>> Replace IPDM E/R. Refer to
PG-27, "Removal and Installation of IPDM E/R"
.
NG
>> Repair harness or connector.
(+)
(
−
)
Voltage
Front combination
lamp connector
Terminal
RH
E24
2
Ground Battery
voltage
LH
E41
2
(+)
(
−
)
Voltage
Front combination
lamp connector
Terminal
RH
E24
2
Ground Battery
voltage
LH
E41
2
PKIA4901E
27 – 2
: Continuity should exist.
28 – 2
: Continuity should exist.
PKIA4902E
LT-22
HEADLAMP - XENON TYPE -
6.
CHECK HEADLAMP GROUND
1.
Check continuity between front combination lamp RH harness
connector E24 terminal 4 and ground.
2.
Check continuity between front combination lamp LH harness
connector E41 terminal 4 and ground.
OK or NG
OK
>> Replace front combination lamp. Refer to
.
NG
>> Repair harness or connector.
Headlamp Does Not Change To High Beam (One Side)
NKS002NQ
1.
CHECK HEADLAMP INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front combination lamp RH or LH connectors.
3.
Turn ignition switch ON.
4.
Lighting switch is turned HIGH BEAM position.
5.
Check voltage between front combination lamp harness connec-
tor and ground.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
CHECK HEADLAMP CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector E7 ter-
minal 27 and front combination lamp RH harness connector E24
terminal 2.
4.
Check continuity between IPDM E/R harness connector E7 ter-
minal 28 and front combination lamp LH harness connector E41
terminal 2.
OK or NG
OK
PG-27, "Removal and Installation of IPDM E/R"
NG
>> Repair harness or connector.
4 – Ground
: Continuity should exist.
4 – Ground
: Continuity should exist.
PKIA4907E
(+)
(
−
)
Voltage
Front combination
lamp connector
Terminal
RH
E24
2
Ground Battery
voltage
LH
E41
2
PKIA4901E
27 – 2
: Continuity should exist.
28 – 2
: Continuity should exist.
PKIA4902E
HEADLAMP - XENON TYPE -
LT-23
C
D
E
F
G
H
I
J
L
M
A
B
LT
3.
CHECK HEADLAMP GROUND
1.
Check continuity between front combination lamp RH harness
connector E24 terminal 4 and ground.
2.
Check continuity between front combination lamp LH harness
connector E41 terminal 4 and ground.
OK or NG
OK
>> Replace front combination lamp. Refer to
NG
>> Repair harness or connector.
Headlamp Does Not Illuminate (Both Sides)
NKS002NS
1.
CHECK COMBINATION SWITCH INPUT SIGNAL
With CONSULT-II
Select “BCM” on CONSULT-II. With “HEAD LAMP” data monitor,
make sure “HEAD LAMP SW 1” and “HEAD LAMP SW 2” turns ON-
OFF linked with operation of lighting switch.
Without CONSULT-II
Refer to
LT-100, "Combination Switch Inspection"
OK or NG
OK
>> GO TO 2.
NG
>> Check combination switch (lighting switch). Refer to
100, "Combination Switch Inspection"
.
2.
HEADLAMP ACTIVE TEST
With CONSULT-II
1.
Select “IPDM E/R” on CONSULT-II, and select “ACTIVE TEST”
on “SELECT DIAG MODE” screen.
2.
Select “LAMPS” on “SELECT TEST ITEM” screen.
3.
Touch “LO” screen.
4.
Make sure headlamp low beam operates.
Without CONSULT-II
1.
Start auto active test. Refer to
.
2.
Make sure headlamp low beam operates.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 4.
4 – Ground
: Continuity should exist.
4 – Ground
: Continuity should exist.
PKIA4907E
When lighting switch is 2ND
position
: HEAD LAMP SW 1 ON
: HEAD LAMP SW 2 ON
PKIA7586E
Headlamp low beam should operate.
Headlamp low beam should operate.
SKIA5774E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст