Infiniti G35 (V35). Manual — part 741
SE-66
AUTOMATIC DRIVE POSITIONER
2.
CHECK TELESCOPIC CIRCUIT HARNESS CONTINUITY
1.
Disconnect automatic drive positioner control unit connector and ADP steering switch connector.
2.
Check continuity between automatic drive positioner control unit
connector M96 terminals 11, 27 and ADP steering switch con-
nector M100 terminals 4, 5.
3.
Check continuity between automatic drive positioner control unit
connector M96 terminals 11, 27 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between automatic drive positioner control unit and ADP steering
switch.
3.
CHECK TELESCOPIC SWITCH
Check continuity between ADP steering switch as follows.
OK or NG
OK
>> GO TO 4.
NG
>> Replace ADP steering switch.
4.
CHECK ADP STEERING SWITCH GROUND CIRCUIT
Check continuity between ADP steering switch connector M100 ter-
minal 1 and ground.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace or replace harness between ADP steering
switch and ground.
11 (P/L) – 5 (P/L)
: Continuity should exist.
27 (G/W) – 4 (G/W)
: Continuity should exist.
11 (P/L) – Ground
: Continuity should not exist.
27 (G/W) – Ground
: Continuity should not exist.
PIIA5071E
Terminal
ADP steering switch condition
Continuity
5
1
FORWARD
Yes
Other than above
No
4
BACKWARD
Yes
Other than above
No
PIIA4481E
1 (B) – Ground
: Continuity should exist.
PIIA3308E
AUTOMATIC DRIVE POSITIONER
SE-67
C
D
E
F
G
H
J
K
L
M
A
B
SE
Check Tilt Switch Circuit
NIS001I8
1.
CHECK FUNCTION
With CONSULT-II
With “TILT SW-UP,TILT SW-DOWN” on the DATA MONITOR, operate the ADP steering switch to check ON/
OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Tilt switch operate, check voltage between automatic drive positioner control unit connector and ground.
OK or NG
OK
>> Tilt switch circuit is OK.
NG
>> GO TO 2.
2.
CHECK TILT SWITCH CIRCUIT HARNESS CONTINUITY
1.
Disconnect automatic drive positioner control unit connector and ADP steering switch connector.
2.
Check continuity between automatic drive positioner control unit
connector M96 terminals 1, 17 and ADP steering switch connec-
tor M100 terminals 2, 3.
3.
Check continuity between automatic drive positioner control unit
connector M96 terminals 1, 17 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between automatic drive positioner control unit and ADP steering
switch.
Monitor item
[OPERATION or UNIT]
Contents
TILT SW-UP
“ON/OFF”
(ON/OFF) status judged from the tilt switch
(UP) signal is displayed.
TILT SW-DOWN
“ON/OFF”
(ON/OFF) status judged from the tilt switch
(DOWN) signal is displayed.
PIIB3410E
Connector
Terminals
(Wire color)
Tilt switch condition
Voltage (V)
(Approx.)
(+)
(–)
M96
1 (Y/G)
Ground
UP
0
Other than above
5
17 (LG/B)
DOWN
0
Other than above
5
PIIA5074E
1 (Y/G) – 2 (Y/G)
: Continuity should exist.
17 (LG/B) – 3 (LG/B)
: Continuity should exist.
1 (Y/G) – Ground
: Continuity should not exist.
17 (LG/B) – Ground
: Continuity should not exist.
PIIA5072E
SE-68
AUTOMATIC DRIVE POSITIONER
3.
CHECK ADP TILT STEERING SWITCH
Check continuity between ADP steering switch as follows.
OK or NG
OK
>> GO TO 6.
NG
>> Replace ADP steering switch.
4.
CHECK ADP STEERING SWITCH GROUND CIRCUIT
Check continuity between ADP steering switch connector M100 ter-
minal 1 and ground.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Repair or replace harness between ADP steering switch
and ground.
Terminal
ADP steering switch condition
Continuity
2
1
UP
Yes
Other than above
No
3
DOWN
Yes
Other than above
No
PIIA4482E
1 (B) – Ground
: Continuity should exist.
PIIA3310E
AUTOMATIC DRIVE POSITIONER
SE-69
C
D
E
F
G
H
J
K
L
M
A
B
SE
Check P Range Switch Circuit (A/T Models)
NIS001I9
1.
CHECK FUNCTION
With CONSULT-II
Make sure when the A/T selector lever is in P position, “P POSI SW” on the DATA MONITOR becomes ON.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and ground.
OK or NG
OK
>> A/T device (park position switch) circuit is OK.
NG
>> GO TO 2.
2.
CHECK PARK POSITION SWITCH POWER SUPPLY CIRCUIT HARNESS
1.
Disconnect driver seat control unit connector and A/T device (park position switch) connector.
2.
Check continuity between driver seat control unit connector
B352 terminal 21 and A/T device (park position switch) connec-
tor M47 terminal 3.
3.
Check continuity between driver seat control unit connector
B352 terminal 21 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between driver seat control
unit and A/T device (park position switch).
Monitor item
[OPERATION or UNIT]
Contents
DETENT SW
“ON/
OFF”
The selector lever position “P position (ON)/other than
P position (OFF)” judged from the detente switch sig-
nal is displayed.
PIIB2072E
Connector
Terminals
(Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
B352
21 (L/Y)
Ground
Selector lever sifted to P
position.
0
Selector lever other than P
position.
5
PIIB7366E
21 (L/Y) – 3 (PU/R)
: Continuity should exist.
21 (L/Y) – Ground
: Continuity should not exist.
PIIB7367E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст