Infiniti G35 (V35). Manual — part 75
REPAIR FOR COMPONENT PARTS
AT-291
D
E
F
G
H
I
J
K
L
M
A
B
AT
b.
Remove 1st one-way clutch from rear sun gear.
5.
Remove seal rings from mid sun gear.
INSPECTION
High and Low Reverse Clutch Hub Snap Ring, Rear Sun Gear Snap Ring
●
Check for deformation, fatigue or damage.
CAUTION:
If necessary, replace the snap ring.
1st One-way Clutch
●
Check frictional surface for wear or damage.
CAUTION:
If necessary, replace the 1st one-way clutch.
Mid Sun Gear
●
Check for deformation, fatigue or damage.
CAUTION:
If necessary, replace the mid sun gear.
Rear Sun Gear
●
Check for deformation, fatigue or damage.
CAUTION:
If necessary, replace the rear sun gear.
High and Low Reverse Clutch Hub
●
Check for deformation, fatigue or damage.
CAUTION:
If necessary, replace the high and low reverse clutch hub.
SCIA4633E
SCIA2861E
AT-292
REPAIR FOR COMPONENT PARTS
ASSEMBLY
1.
Install seal rings to mid sun gear.
CAUTION:
●
Do not reuse seal rings.
●
Apply petroleum jelly to seal rings.
2.
Install 1st one-way clutch to rear sun gear.
CAUTION:
Apply petroleum jelly to 1st one-way clutch.
3.
Using a flat-bladed screwdriver, install snap ring to rear sun
gear.
4.
Install rear sun gear assembly (1) to mid sun gear assembly.
SCIA2861E
SCIA4633E
SCIA2859E
SCIA8155E
REPAIR FOR COMPONENT PARTS
AT-293
D
E
F
G
H
I
J
K
L
M
A
B
AT
5.
Install needle bearing to high and low reverse clutch hub.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-262, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
●
Apply petroleum jelly to needle bearing.
6.
Install high and low reverse clutch hub to mid sun gear assem-
bly.
7.
Using pair of snap ring pliers, install snap ring to mid sun gear
assembly.
CAUTION:
Do not expand snap ring excessively.
8.
Check operation of 1st one-way clutch.
a.
Hold mid sun gear and turn rear sun gear.
b.
Check 1st one-way clutch for correct locking and unlocking
directions.
CAUTION:
If not as shown in the figure, check installation direction of
1st one-way clutch.
9.
Install needle bearing and bearing race to high and low reverse
clutch hub.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-262, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
●
Apply petroleum jelly to needle bearing.
SCIA2857E
SCIA2856E
SCIA2855E
SCIA3132E
SCIA2854E
AT-294
REPAIR FOR COMPONENT PARTS
High and Low Reverse Clutch
NCS000J9
COMPONENTS
DISASSEMBLY
1.
Remove bearing race from high and low reverse clutch drum.
2.
Using a flat-bladed screwdriver, remove snap ring from high and
low reverse clutch drum.
3.
Remove drive plates, driven plates and retaining plate from high
and low reverse clutch drum.
1.
High and low reverse clutch drum
2.
Driven plate
3.
Retaining plate
4.
Snap ring
5.
Drive plate
6.
Bearing race
SCIA5239E
SCIA5215E
SCIA2868E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст