Infiniti G35 (V35). Manual — part 76
REPAIR FOR COMPONENT PARTS
AT-295
D
E
F
G
H
I
J
K
L
M
A
B
AT
INSPECTION
●
Check the following, and replace high and low reverse clutch assembly if necessary.
High and Low Reverse Clutch Snap Ring
●
Check for deformation, fatigue or damage.
High and Low Reverse Clutch Drive Plates
●
Check facing for burns, cracks or damage.
High and Low Reverse Clutch Retaining Plate and Driven Plates
●
Check facing for burns, cracks or damage.
ASSEMBLY
1.
Install drive plates, driven plates and retaining plate in high and
low reverse clutch drum.
CAUTION:
Take care with order of plates.
●
Snap ring (1)
●
Retaining plate (2)
●
Drive plate (3)
●
Driven plate (4)
●
Drive plate/Driven plate: 4/4
2.
Using a flat-bladed screwdriver, install snap ring in high and low
reverse clutch drum.
3.
Install bearing race to high and low reverse clutch drum.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-262, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
●
Apply petroleum jelly to needle bearing.
SCIA6735E
SCIA2868E
SCIA5215E
AT-296
REPAIR FOR COMPONENT PARTS
Direct Clutch
NCS000JA
COMPONENTS
DISASSEMBLY
1.
Using a flat-bladed screwdriver, remove snap ring from direct
clutch drum.
2.
Remove drive plates, driven plates, dish plate and retaining
plate from direct clutch drum.
INSPECTION
●
Check the following, and replace direct clutch assembly if necessary.
Direct Clutch Snap Ring
●
Check for deformation, fatigue or damage.
Direct Clutch Drive Plates
●
Check facing for burns, cracks or damage.
Direct Clutch Retaining Plate and Driven Plates
●
Check facing for burns, cracks or damage.
1.
Direct clutch drum
2.
Dish plate
3.
Retaining plate
4.
Driven plate
5.
Retaining plate
6.
Snap ring
7.
Drive plate
SCIA7015E
SCIA2868E
REPAIR FOR COMPONENT PARTS
AT-297
D
E
F
G
H
I
J
K
L
M
A
B
AT
ASSEMBLY
1.
Install drive plates, driven plates, dish plate and retaining plate
in direct clutch drum.
CAUTION:
Take care with order of plates.
●
Snap ring (1)
●
Retaining plate (2)
●
Drive plate (3)
●
Driven plate (4)
●
Dish plate (5)
●
Drive plate/Driven plate: 5/4
2.
Using a flat-bladed screwdriver, install snap ring in direct clutch
drum.
SCIA6952E
SCIA2868E
AT-298
ASSEMBLY
ASSEMBLY
PFP:00000
Assembly (1)
NCS000JB
1.
As shown in the figure, use a drift [commercial service tool 22
mm (0.87 in) dia.] to drive manual shaft oil seals into the trans-
mission case until it is flush.
CAUTION:
●
Do not reuse manual shaft oil seals.
●
Apply ATF to manual shaft oil seals.
2.
Install detent spring and spacer in transmission case, and then
tighten detent spring and spacer mounting bolt to the specified
torque. Refer to
3.
Install manual shaft to transmission case.
4.
Install parking rod to manual plate.
SCIA5259E
SCIA5248E
SCIA5716E
SCIA5220E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст