Infiniti G35 (V35). Manual — part 29
DTC P0705 PARK/NEUTRAL POSITION SWITCH
AT-107
D
E
F
G
H
I
J
K
L
M
A
B
AT
Wiring Diagram — AT — PNP/SW
NCS000CV
TCWM0248E
AT-108
DTC P0705 PARK/NEUTRAL POSITION SWITCH
Diagnostic Procedure
NCS000CW
1.
CHECK PNP SW CIRCUIT
With CONSULT-II
1.
Turn ignition switch ON.
2.
Select “SELECTION FROM MENU” in “DATA MONITOR” mode
for “A/T” with CONSULT-II.
3.
Check if correct selector lever position (N/P, R or D) is displayed
as selector lever is moved into each position.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 2.
2.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
AT-172, "MAIN POWER SUPPLY AND GROUND CIR-
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace damaged parts.
Item name
Condition
Display value
SLCT LVR POSI
Selector lever in “N” and “P” positions.
N/P
Selector lever in “R” position.
R
Selector lever in “D” position.
D
SCIA5296E
DTC P0705 PARK/NEUTRAL POSITION SWITCH
AT-109
D
E
F
G
H
I
J
K
L
M
A
B
AT
4.
CHECK SUB-HARNESS
1.
Remove control valve with TCM. Refer to
AT-225, "Control Valve with TCM and A/T Fluid Temperature
.
2.
Disconnect park/neutral position switch connector and TCM connector.
3.
Check continuity between park/neutral position switch connector
terminals and TCM connector terminals.
4.
If OK, check harness for short to ground and short to power.
5.
Reinstall any part removed.
OK or NG
OK
>> Replace control valve with TCM. Refer to
AT-225, "Control Valve with TCM and A/T Fluid Temper-
.
NG
>> Replace open circuit or short to ground and short to power in harness or connectors.
5.
CHECK DTC
Perform
AT-106, "DTC Confirmation Procedure"
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
Item
Connector
Terminal
Continuity
Park/neutral position switch
connector
F505
1
Yes
TCM connector
F503
13
Park/neutral position switch
connector
F505
2
Yes
TCM connector
F503
11
Park/neutral position switch
connector
F505
3
Yes
TCM connector
F503
12
Park/neutral position switch
connector
F505
5
Yes
TCM connector
F503
14
SCIA5457E
AT-110
DTC P0717 TURBINE REVOLUTION SENSOR
DTC P0717 TURBINE REVOLUTION SENSOR
PFP:31935
Description
NCS000EG
The turbine revolution sensor detects input shaft rpm (revolutions per minute). It is located on the input side of
the A/T. Monitors revolution of sensor 1 and sensor 2 for non-standard conditions.
CONSULT-II Reference Value
NCS000EH
On Board Diagnosis Logic
NCS000EI
●
This is an OBD-II self-diagnostic item.
●
Diagnostic trouble code “P0717 TURBINE REV S/CIRC” with CONSULT-II or 11th judgment flicker with-
out CONSULT-II is detected under the following conditions.
–
When TCM does not receive the proper voltage signal from the sensor.
–
When TCM detects an irregularity only at position of 4th gear for turbine revolution sensor 2.
Possible Cause
NCS000EJ
●
Harness or connectors.
(Sensor circuit is open or shorted.)
●
Turbine revolution sensor 1 and/or 2.
DTC Confirmation Procedure
NCS000EK
CAUTION:
●
Always drive vehicle at a safe speed.
●
Be careful not to rev engine into the red zone on the tachometer.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “SELECTION FROM MENU” in “DATA MONITOR” mode
for “A/T” with CONSULT-II and check monitor “VHCL/S SE-A/T”,
“ACCELE POSI”, “ENGINE SPEED”, “SLCT LVR POSI” and
“GEAR”.
3.
Touch “START”.
4.
Start engine and maintain the following conditions for at least 5
consecutive seconds.
VHCL/S SE-A/T: 40 km/h (25 MPH) or more
ACCELE POSI: More than 0.5/8
ENGINE SPEED: 1,500 rpm or more
SLCT LVR POSI: “D” position
GEAR (Turbine revolution sensor 1): “4” or “5” position
GEAR (Turbine revolution sensor 2): All positions
Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving
conditions required for this test.
5.
If DTC is detected, go to
AT-111, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II”.
Item name
Condition
Display value
TURBINE REV
During driving (lock-up ON)
Approximately matches the engine speed.
BCIA0031E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст