Infiniti G35 (V35). Manual — part 371
DTC P0300 - P0306 MULTIPLE CYLINDER MISFIRE, NO. 1 - 6 CYLINDER MIS-
FIRE
EC-365
C
D
E
F
G
H
I
J
K
L
M
A
EC
6.
CHECK FUNCTION OF IGNITION COIL-I
CAUTION:
Do the following procedure in the place where ventilation is good without the combustible.
1.
Turn ignition switch OFF.
2.
Reconnect all harness connectors disconnected.
3.
Remove fuel pump fuse in IPDM E/R to release fuel pressure.
NOTE:
Do not use CONSULT-II to release fuel pressure, or fuel pres-
sure applies again during the following procedure.
4.
Start engine.
5.
After engine stalls, crank it two or three times to release all fuel
pressure.
6.
Turn ignition switch OFF.
7.
Remove all ignition coil harness connectors to avoid the electri-
cal discharge from the ignition coils.
8.
Remove ignition coil and spark plug of the cylinder to be
checked.
9.
Crank engine for 5 seconds or more to remove combustion gas in the cylinder.
10. Connect spark plug and harness connector to ignition coil.
11. Fix ignition coil using a rope etc. with gap of 13 - 17 mm
between the edge of the spark plug and grounded metal portion
as shown in the figure.
12. Crank engine for about 3 seconds, and check whether spark is
generated between the spark plug and the grounded metal por-
tion.
CAUTION:
●
Do not approach to the spark plug and the ignition coil
within 50cm. Be careful not to get an electrical shock
while checking, because the electrical discharge voltage
becomes 20kV or more.
●
It might cause to damage the ignition coil if the gap of more than 17 mm is taken.
NOTE:
When the gap is less than 13 mm, the spark might be generated even if the coil is malfunctioning.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 7.
7.
CHECK FUNCTION OF IGNITION COIL-II
1.
Turn ignition switch OFF.
2.
Disconnect spark plug and connect a known-good spark plug.
3.
Crank engine for about 3 seconds, and recheck whether spark is generated between the spark plug and
the grounded metal portion.
OK or NG
OK
>> GO TO 8.
NG
>> Check ignition coil, power transistor and their circuits. Refer to
Spark should be generated.
PBIB1910E
PBIB2325E
Spark should be generated.
EC-366
DTC P0300 - P0306 MULTIPLE CYLINDER MISFIRE, NO. 1 - 6 CYLINDER MIS-
FIRE
8.
CHECK SPARK PLUG
Check the initial spark plug for fouling, etc.
OK or NG
OK
>> Replace spark plug(s) with standard type one(s). For
spark plug type, refer to
.
NG
>> 1. Repair or clean spark plug.
2. GO TO 9.
9.
CHECK FUNCTION OF IGNITION COIL-III
1.
Reconnect the initial spark plugs.
2.
Crank engine for about 3 seconds, and recheck whether spark is generated between the spark plug and
the grounded portion.
OK or NG
OK
>> INSPECTION END
NG
>> Replace spark plug(s) with standard type one(s). For spark plug type, refer to
Spark Plugs (Platinum-Tipped Type)"
10.
CHECK COMPRESSION PRESSURE
Check compression pressure. Refer to
EM-119, "CHECKING COMPRESSION PRESSURE"
.
OK or NG
OK
>> GO TO 11.
NG
>> Check pistons, piston rings, valves, valve seats and cylinder head gaskets.
11.
CHECK FUEL PRESSURE
1.
Install all removed parts.
2.
Release fuel pressure to zero. Refer to
EC-81, "FUEL PRESSURE RELEASE"
3.
Install fuel pressure gauge and check fuel pressure. Refer to
OK or NG
OK
>> GO TO 13.
NG
>> GO TO 12.
12.
DETECT MALFUNCTIONING PART
Check the following.
●
Fuel pump and circuit (Refer to
●
Fuel pressure regulator (Refer to
●
Fuel lines (Refer tor
●
Fuel filter for clogging
>> Repair or replace.
SEF156I
Spark should be generated.
At idle: Approximately 350 kPa (3.57 kg/cm
2
, 51 psi)
DTC P0300 - P0306 MULTIPLE CYLINDER MISFIRE, NO. 1 - 6 CYLINDER MIS-
FIRE
EC-367
C
D
E
F
G
H
I
J
K
L
M
A
EC
13.
CHECK IGNITION TIMING
Check the following items. Refer to
OK or NG
OK
>> GO TO 14.
NG
>> Follow the
Items
Specifications
Target idle speed
A/T: 650
±
50 rpm (in P or N position)
M/T: 650
±
50 rpm (in Neutral position)
Ignition timing
A/T: 15
±
5
°
BTDC (in P or N position)
M/T: 15
±
5
°
BTDC (in Neutral position)
EC-368
DTC P0300 - P0306 MULTIPLE CYLINDER MISFIRE, NO. 1 - 6 CYLINDER MIS-
FIRE
14.
CHECK A/F SENSOR 1 INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect A/F sensor 1 harness connector.
3.
Disconnect ECM harness connector.
4.
Check harness continuity between the following terminals.
Refer to Wiring Diagram.
5.
Check harness continuity between the following terminals and ground.
Refer to Wiring Diagram.
6.
Also check harness for short to power.
OK or NG
OK
>> GO TO 15.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
15.
CHECK A/F SENSOR 1 HEATER
Refer to
EC-182, "Component Inspection"
OK or NG
OK
>> GO TO 16.
NG
>> Replace malfunctioning A/F sensor 1.
A/F sensor 1 terminal
ECM terminal
Bank 1
1
16
2
75
5
35
6
56
Bank 2
1
76
2
77
5
57
6
58
Continuity should exist.
Bank 1
Bank 2
A/F sensor 1 terminal
ECM terminal
A/F sensor 1 terminal
ECM terminal
1
16
1
76
2
75
2
77
5
35
5
57
6
56
6
58
Continuity should not exist.
PBIB2100E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст