Infiniti G35 (V35). Manual — part 110
TROUBLE DIAGNOSIS
ATC-111
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Multiplex Communication Circuit
NJS0003U
DIAGNOSIS PROCEDURE FOR MULTIPLEX COMMUNICATION
SYMPTOM: A/C system cannot be controlled.
1.
CHECK DISPLAY AND A/C AUTO AMP. OUTPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check multiplex communication signal between display and A/C
auto amp. harness connector M31 terminals 15, 35 and ground
using an oscilloscope.
OK or NG
OK
>> GO TO 2.
NG
>> Replace display and A/C auto amp.
RJIA3540E
Terminals
Voltage
(+)
(
−
)
Display and A/C
auto amp. connector
Terminal No.
M31
15
Ground
M31
35
RJIA3541E
RJIA0212E
SJIA1479J
ATC-112
TROUBLE DIAGNOSIS
2.
CHECK CIRCUIT CONTINUITY BETWEEN A/C AND AUDIO CONTROLLER AND DISPLAY AND A/C
AUTO AMP.
1.
Turn ignition switch OFF.
2.
Disconnect A/C and audio controller connector and display and
A/C auto amp. connector.
3.
Check continuity between A/C and audio controller harness con-
nector M38 terminals 6, 5 and display and A/C auto amp. har-
ness connector M31 terminals 15, 35.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK DISPLAY AND A/C AUTO AMP. INPUT SIGNAL
1.
Reconnect A/C and audio controller connector and display and
A/C auto amp. connector.
2.
Turn ignition switch ON.
3.
Confirm multiplex communication signal between display and A/
C auto amp. harness connector M31 terminal 14 and ground
using an oscilloscope.
OK or NG
OK
>> Replace display and A/C auto amp.
NG
>> GO TO 4.
4.
CHECK CIRCUIT CONTINUITY BETWEEN A/C AND AUDIO CONTROLLER AND DISPLAY AND A/C
AUTO AMP.
1.
Turn ignition switch OFF.
2.
Disconnect A/C and audio controller connector and display and
A/C auto amp. connector.
3.
Check continuity between A/C and audio controller harness con-
nector M38 terminal 7 and display and A/C auto amp. harness
connector M31 terminal 14.
OK or NG
OK
>> Replace A/C and audio controller.
NG
>> Repair harness or connector.
6 – 15
: Continuity should exist.
5 – 35
: Continuity should exist.
RJIA3542E
Terminals
Voltage
(+)
(
−
)
Display and A/C
auto amp. connector
Terminal No.
M31
14
Ground
RJIA3543E
RJIA0213E
7 – 14
: Continuity should exist.
RJIA3544E
A/C AND AUDIO CONTROLLER
ATC-113
C
D
E
F
G
H
I
K
L
M
A
B
ATC
A/C AND AUDIO CONTROLLER
PFP:28074
Removal and Installation
NJS0003V
REMOVAL
Refer to
AV-33, "Removal and Installation for A/C and Audio Controller"
.
INSTALLATION
Installation is basically the reverse order of removal.
ATC-114
AUTO AMP
AUTO AMP
PFP:27760
Removal and Installation of Display and A/C Auto Amp.
NJS0003W
REMOVAL
1.
Remove cluster lid finisher. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
2.
Remove mounting screws, and then remove display and A/C
auto amp.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA3583E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст