Infiniti G35 (V35). Manual — part 465
DRIVE BELTS
EM-15
C
D
E
F
G
H
I
J
K
L
M
A
EM
ALTERNATOR AND POWER STEERING OIL PUMP BELT
1.
Remove undercover with power tool.
2.
Loosen idler pulley lock nut (A) and adjust tension by turning
adjusting bolt (B).
●
For specified belt tension. Refer to
3.
Tighten nut (A).
A/C COMPRESSOR BELT
1.
Remove undercover with power tool.
2.
Loosen idler pulley lock nut (C) and adjust tension by turning adjusting bolt (D).
●
For specified belt tension. Refer to
.
3.
Tighten nut (C).
Removal and Installation
NBS000JQ
REMOVAL
1.
Remove undercover with power tool.
2.
Remove alternator and power steering oil pump belt. Refer to
3.
Remove A/C compressor belt. Refer to
CAUTION:
Grease is applied to idler pulley adjusting bolt. Be careful to keep grease away from belt.
INSTALLATION
1.
Install belts to pulley in the reverse order of removal.
CAUTION:
●
Make sure belt is correctly engaged with the pulley groove.
●
Check for engine oil and engine coolant are not adhered to belt and each pulley groove.
2.
3.
Tighten each adjusting bolt and nut to the specified torque.
4.
Make sure that tension of each belt is within the standard.
: 34.8 N·m (3.5 kg-m, 26 ft-lb)
PBIC1406E
: 34.8 N·m (3.5 kg-m, 26 ft-lb)
EM-16
AIR CLEANER AND AIR DUCT
AIR CLEANER AND AIR DUCT
PFP:16500
Components
NBS000JR
Removal and Installation
NBS000JS
REMOVAL
1.
Remove engine cover with power tool. Refer to
EM-18, "INTAKE MANIFOLD COLLECTOR"
●
This work is unnecessary when parts located forward of mass air flow sensor are removed/installed.
2.
Remove air duct (inlet).
3.
Disconnect harness connector from mass air flow sensor.
4.
Disconnect PCV hose.
5.
Remove air cleaner case/mass air flow sensor assembly and air duct disconnecting their joints.
●
Add marks as necessary for easier installation.
6.
Remove mass air flow sensor from air cleaner case.
CAUTION:
Handle mass air flow sensor with care.
●
Do not shock it.
●
Do not disassemble it.
●
Do not touch its sensor.
7.
Remove resonator in fender, lifting left fender protector.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Air hose
2.
PCV hose
3.
Air duct
4.
Air hose
5.
Power duct
6.
Clip
7.
Air duct (inlet)
8.
Resonator
9.
Grommet
10. Air cleaner case
11.
Air cleaner filter
12. Air cleaner case
13. O-ring
14. Mass air flow sensor
PBIC2278E
AIR CLEANER AND AIR DUCT
EM-17
C
D
E
F
G
H
I
J
K
L
M
A
EM
●
Align marks. Attach each joint. Screw clamps firmly.
●
To position air cleaner case. Refer to
EM-17, "Changing Air Cleaner Filter"
Changing Air Cleaner Filter
NBS000JT
INSPECTION
●
Check status (fouling, damage, etc.) of air cleaner filter at power
duct hole.
REMOVAL
1.
Remove air duct (inlet) from air cleaner case.
2.
Disconnect harness connector from mass air flow sensor.
3.
Loosen clamp bolts of air hose.
4.
Remove mounting bolts for air cleaner case. Remove air cleaner
case/mass air flow sensor/air hose assembly.
5.
Unfasten clips and open air cleaner case, and remove air
cleaner filter.
INSTALLATION
Note the following, and install in the reverse order of removal.
●
If grommet at bottom of air cleaner case comes off together with
air cleaner case, fix it to vehicle before installation.
●
Look at internal bottom face through power duct hole, and posi-
tion air cleaner case with resonator upper end circle and air
cleaner case round hole aligned. Then push air cleaner case
straight down.
●
At this time, check by hand if protrusion at bottom of air cleaner
case has been inserted into grommet on vehicle side.
●
Clip power duct with bulge on reverse side of lower end
engaged with air cleaner case.
PBIC1217E
PBIC0770E
PBIC1218E
KBIA0954E
EM-18
INTAKE MANIFOLD COLLECTOR
INTAKE MANIFOLD COLLECTOR
PFP:14003
Components
NBS000JU
●
Refer to
for symbol marks in the figure.
Removal and Installation
NBS000JV
REMOVAL
WARNING:
●
To avoid the danger of being scalded, do not drain the engine coolant when the engine is hot.
●
Gasket for intake manifold collector (upper) is secured together with mounting bolt for intake man-
ifold collector (lower). Thus, even when only gasket for upper side is replaced, gasket for lower
side must be also replaced.
1.
Vacuum hose
2.
EVAP canister purge volume con-
trol solenoid valve
3.
Vacuum hose
4.
Bracket
5.
Intake manifold collector (upper)
6.
Water hose
7.
Water hose
8.
Gasket
9.
Electric throttle control actuator
10. Bracket
11.
PCV hose
12. Bracket
13. Gasket
14. Intake manifold collector (lower)
15. Gasket
16. Intake manifold collector cover
A.
To vacuum pipe
B.
To water outlet
C.
To heater pipe
D.
To PCV valve
KBIA3590J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст