Infiniti G35 (V35). Manual — part 712
RSU-14
FRONT LOWER LINK
FRONT LOWER LINK
PFP:55110
Removal and Installation
NES0002T
REMOVAL
1.
Remove tires from vehicle with power tool.
2.
Set jack under rear lower link.
3.
Remove mounting nut and bolt between front lower link and rear suspension member with power tool.
4.
Remove mounting nut and bolt between front lower link and axle with power tool.
5.
Remove front lower link from vehicle.
INSPECTION AFTER REMOVAL
Check front lower link and bushing for any deformation, cracks, or damage. Replace if necessary.
INSTALLATION
●
Refer to
for tightening torque. Install in the reverse order of removal.
NOTE:
Refer to component parts location and do not reuse non-reusable parts.
●
Perform final tightening of rear suspension member and axle installation position (rubber bushing) under
unladen condition with tires on level ground. Check wheel alignment. Refer to
.
REAR LOWER LINK & COIL SPRING
RSU-15
C
D
F
G
H
I
J
K
L
M
A
B
RSU
REAR LOWER LINK & COIL SPRING
PFP:551B0
Removal and Installation
NES0002U
REMOVAL
1.
Remove tires from vehicle with power tool.
2.
Set jack under rear lower link.
3.
Loosen mounting bolt and nut of rear lower link in side of suspension member, and then remove mounting
bolt and nut in side of axle with power tool.
4.
Slowly lower jack, then remove upper seat, coil spring and rubber sheet from rear lower link.
5.
Remove mounting bolt and nut in side of rear suspension member to remove rear lower link with power
tool.
INSPECTION AFTER REMOVAL
Check rear lower link, bushing and coil spring for deformation, cracks, and damage. Replace rear lower link
and coil spring if necessary.
INSTALLATION
●
Refer to
for tightening torque. Install in the reverse order of removal.
NOTE:
Refer to component parts location and do not reuse non-reusable parts.
●
Check that upper seat is attached as shown in the figure.
NOTE:
Insert bracket tabs (3) and the inside protrusion on upper seat
into each other beforehand as shown in the figure.
●
Match up rubber seat indentions and rear lower link grooves and
attach.
NOTE:
Make sure spring is not up side down. The top and bottom are
indicated by paint color.
●
Perform final tightening of rear suspension member and axle
installation position (rubber bushing) under unladen condition
with tires on level ground. Check wheel alignment. Refer to
RSU-5, "Wheel Alignment Inspection"
SEIA0229E
RSU-16
STABILIZER BAR
STABILIZER BAR
PFP:56230
Removal and Installation
NES0002V
REMOVAL
1.
Remove mounting bolts and remove stabilizer connecting rod mount bracket from suspension arm.
2.
Remove lower side mounting nut on stabilizer connecting rod and remove stabilizer connecting rod from
stabilizer bar with power tool.
3.
Remove mounting nut on stabilizer clamp and remove stabilizer from vehicle with power tool.
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer bushings, stabilizer clamps, stabilizer connecting rod, stabilizer connecting rod
mounting bracket for any deformation, crack or damage. Replace if necessary.
INSTALLATION
●
Refer to
for tightening torque. Install in the reverse order of removal.
NOTE:
Refer to component parts location and do not reuse non-reusable parts.
REAR SUSPENSION MEMBER
RSU-17
C
D
F
G
H
I
J
K
L
M
A
B
RSU
REAR SUSPENSION MEMBER
PFP:55501
Removal and Installation
NES0002W
REMOVAL
1.
Remove tires from vehicle with power tool.
2.
Remove brake caliper with power tool. Hang it in a place where it will not interfere with work. Refer to
NOTE:
Avoid depressing brake pedal while brake caliper is removed.
3.
Remove exhaust front tube. Refer to
.
4.
Remove stabilizer bar. Refer to
5.
Remove drive shaft. Refer to
6.
RFD-17, "REAR FINAL DRIVE ASSEMBLY"
.
7.
Separate the attachment between parking brake cable and vehicle and rear suspension member. Refer to
.
8.
Remove rear lower link and coil spring. Refer to
RSU-15, "REAR LOWER LINK & COIL SPRING"
.
9.
Remove mounting bolt in lower side of shock absorber. Refer to
10. Set jack under rear suspension member.
11. Remove mounting bolts and nuts tunnel stay and member stay from vehicle.
12. Remove mounting bolts and nuts of rear pin stay and then remove rear pin stay from vehicle.
13. Slowly lowering jack, then remove rear suspension member, suspension arm, radius rod, front lower link
and axle from vehicle as a unit.
14. Remove mounting bolts and nuts, then remove suspension arm, front lower link, radius rod from rear sus-
pension member.
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, and other damage and replace if necessary.
INSTALLATION
●
Refer to
, for tightening torque. Install in the reverse order of removal.
NOTE:
Refer to component parts location and do not reuse non-reusable parts.
●
Perform final tightening of installation position of links (rubber bushing) under unladen condition with tires
on level ground. Check wheel alignment. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст