Infiniti G35 (V35). Manual — part 758
SE-134
FRONT SEAT
FRONT SEAT
PFP:87000
Removal and Installation
NIS000IN
CAUTION:
Do not disassembly the component parts of only front passenger seat in the dotted lines shown in the
figure below.
FRONT SEAT
SE-135
C
D
E
F
G
H
J
K
L
M
A
B
SE
1.
Walk-in lever
2.
Seatback frame assembly
3.
Inner cloth stay
4.
Side air bag module
5.
Walk-in control cable
6.
Headrest
7.
Seat belt hook finisher
8.
Seat belt hook
9.
Headrest holder (locked)
PIIB7397E
SE-136
FRONT SEAT
REMOVAL
When removing or installing the seat trim, carefully handle it to keep dirt out and avoid damage.
CAUTION:
●
Before removing the front seat, turn the ignition switch off, disconnect both battery cables and
wait and least 3 minutes.
●
When checking the power seat circuit for continuity using a circuit tester, do not confuse its con-
nector with the side air bag module connector. Such an error may cause the air bag to deploy.
●
Do not drop, tilt, or bump the side air bag module installing in the seat. Always handle it with care.
1.
Remove the front leg cover and rear leg cover. (LH/RH)
NOTE:
1. Slide the seat backward, and disconnect the front tabs on the front leg cover. Then move the cover
toward the rear of the vehicle, and pull up to remove.
2. Slide the seat forward, then disengage the tabs on the front LH/RH of the rear leg cover and tabs
engaged into the rail. Then pull the cover toward the rear of the vehicle.
2.
Slide the seat until the body mounting bolts are visible and a tool can be inserted.
NOTE:
When disassembling the driver seat after removal, set the front/rear cushion lifter to the top position.
3.
Remove the body mounting bolts.
4.
Disconnect both battery cables.
5.
Remove the harness connector for the side air bag module.
6.
Remove the power seat harness connector and vehicle harness fixing clip out of the vehicle.
NOTE:
When removing and installing, using clothes, protect the parts from damage where it may interfere with
others.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Be sure to insert the rear end tab of the rear leg cover under the rail.
10.
Headrest holder (free)
11. Seatback pad
12. Seatback trim and heater
13.
Lumber support lever knob
14. Reclining device (LH)
15. Reclining device rod
16.
Reclining device (RH)
17. Seat cushion pad
18. Seat cushion trim and heater
19.
Power seat harness
20. Reclining lever
21. Seat cushion outer finisher
22.
Seat cushion outer finisher
23. Power seat switch
24. Seat belt buckle
25.
Seat cushion inner finisher
26. Seat cushion rail assembly
27. Power seat control unit
28.
Seat cushion front finisher
29. Seatback switch
30. Walk-in side lever finisher
31.
Snap ring
32. Walk-in side lever
PIIA1154E
FRONT SEAT
SE-137
C
D
E
F
G
H
J
K
L
M
A
B
SE
Disassembly and Assembly
NIS000IO
SEATBACK TRIM AND PAD
CAUTION:
Do not disassemble front passenger seat cushion assembly.
Always replace as an assembly.
For front passenger seat service parts, refer to the service part catalogue.
NOTE:
Be sure to set the front/rear cushion lifter to the top position.
Disassembly
1.
Remove screw, and then remove walk-in lever.
2.
Disconnect the harness connector, and then remove seatback switch.
3.
Remove seat belt hook finisher.
4.
Remove screw, and then remove seat belt hook.
5.
Open fastener on back of seatback, and remove retainer from
seatback frame.
6.
Pull snap ring upward, and remove lumber support lever knob
from seatback frame.
PIIA3654E
PIIA3655E
PIIA1156E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст