Infiniti G35 (V35). Manual — part 276
WARNING CHIME
DI-51
C
D
E
F
G
H
I
J
L
M
A
B
DI
2.
CHECK DRIVER SIDE DOOR SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and driver side door switch connec-
tor.
3.
Check continuity between BCM harness connector B4 terminal
62 (Y) and driver side door switch harness connector B17 termi-
nal 1 (G/B).
4.
Check continuity between BCM harness connector B4 terminal
62 (Y) and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK DRIVER SIDE DOOR SWITCH
Check driver side door switch. Refer to
DI-56, "DRIVER SIDE DOOR SWITCH"
OK or NG
OK
>> Replace BCM. Refer to
BCS-16, "Removal and Installation of BCM"
.
NG
>> Replace driver side door switch.
Key Switch Signal Inspection (Without Intelligent Key)
NKS000LN
1.
CHECK BCM INPUT SIGNAL
With CONSULT-ll
1.
Select “BCM”.
2.
With “DATA MONITOR” of “BUZZER”, confirm “KEY ON SW”
when the key switch is operated.
Without CONSULT-ll
Check voltage between BCM harness connector M1 terminal 37 (B/
P) and ground.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
62 (Y) – 1 (G/B)
: Continuity should exist.
62 (Y) – Ground
: Continuity should not exist.
SKIA8467E
“KEY ON SW”
When key is inserted to ignition key cylinder
: ON
When key is removed from ignition key cylinder
: OFF
SKIA1960E
37 (B/P) – Ground
When key is inserted to
ignition key cylinder
: Approx. 12 V
When key is removed from
ignition key cylinder
: Approx. 0 V
SKIA5048E
DI-52
WARNING CHIME
2.
CHECK KEY SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect key switch connector.
3.
.
OK or NG
OK
>> GO TO 3.
NG
>> Replace key switch.
3.
CHECK KEY SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector M1 terminal
37 (B/P) and key switch harness connector M307 terminal 1 (B/
P).
3.
Check continuity between BCM harness connector M1 terminal
37 (B/P) and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair harness or connector.
4.
CHECK KEY SWITCH POWER SUPPLY CIRCUIT
Check voltage between key switch harness connector M307 terminal
2 (L/W) and ground.
OK or NG
OK
>> Replace BCM. Refer to
BCS-16, "Removal and Installa-
NG
>> Check harness between key switch and fuse.
37 (B/P) – 1 (B/P)
: Continuity should exist.
37 (B/P) – Ground
: Continuity should not exist.
PKIB3833E
2 (L/W) – Ground
: Battery voltage
SKIA5051E
WARNING CHIME
DI-53
C
D
E
F
G
H
I
J
L
M
A
B
DI
Key Switch and Ignition Knob Switch Signal Inspection (With Intelligent Key,
When Mechanical Key Is Used)
NKS000R8
1.
CHECK BCM INPUT SIGNAL
With CONSULT-ll
1.
Select “BCM”.
2.
With “DATA MONITOR” of “BUZZER”, confirm “KEY ON SW”
when the key is operated.
Without CONSULT-ll
Check voltage between BCM harness connector M1 terminal 37 (B/
P) and ground.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
2.
CHECK KEY SWITCH AND IGNITION KNOB SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect key switch and ignition knob switch connector.
3.
Check key switch and ignition knob switch. Refer to
DI-56, "KEY SWITCH AND IGNITION KNOB
OK or NG
OK
>> GO TO 3.
NG
>> Replace key switch and ignition knob switch.
3.
CHECK KEY SWITCH AND IGNITION KNOB SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector M1 terminal
37 (B/P) and key switch and ignition knob switch harness con-
nector M310 terminal 4 (B/P).
3.
Check continuity between BCM harness connector M1 terminal
37 (B/P) and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair harness or connector.
“KEY ON SW”
When key is inserted to ignition key cylinder
: ON
When key is removed from ignition key cylinder
: OFF
SKIA1960E
37 (B/P) – Ground
When key is inserted to ignition
key cylinder
: Approx. 12 V
When key is removed from
ignition key cylinder
: Approx. 0 V
SKIA5048E
37 (B/P) – 4 (B/P)
: Continuity should exist.
37 (B/P) – Ground
: Continuity should not exist.
PKIB3834E
DI-54
WARNING CHIME
4.
CHECK KEY SWITCH AND IGNITION KNOB SWITCH POWER SUPPLY CIRCUIT
Check voltage between key switch and ignition knob switch harness
connector M310 terminal 3 (Y) and ground.
OK or NG
OK
>> Replace BCM. Refer to
BCS-16, "Removal and Installa-
NG
>> Check harness between key switch and ignition knob
switch and fuse.
Lighting Switch Signal Inspection
NKS000LO
1.
CHECK BCM INPUT SIGNAL
1.
Select “BCM” on CONSULT-II.
2.
With “DATA MONITOR” of “BUZZER”, confirm “LIGHT SW 1ST”
when the lighting switch is operated.
OK or NG
OK
>> INSPECTION END
NG
>> Check lighting switch. Refer to
Seat Belt Buckle Switch (Driver Side) Signal Inspection
NKS000LP
1.
CHECK BCM INPUT SIGNAL
1.
Select “BCM” on CONSULT-II.
2.
With “DATA MONITOR” of “BUZZER”, confirm “BUCKLE SW”
when the seat belt buckle switch (driver side) is operated.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
2.
CHECK COMBINATION METER INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between combination meter harness connector
M20 terminal 47 (BR) and ground.
OK or NG
OK
>> Replace combination meter.
NG
>> GO TO 3.
3 (Y) – Ground
: Battery voltage
SKIA5063E
“LIGHT SW 1ST”
Lighting switch (1st position)
: ON
Lighting switch (OFF)
: OFF
PKIB1956E
“BUCKLE SW”
When seat belt is fastened
: OFF
When seat belt is unfastened
: ON
SKIA8674E
47 (BR) – Ground
When seat belt is fastened
: Approx. 12 V
When seat belt is unfastened
: Approx. 0 V
PKIB2685E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст