Infiniti G20 (P11). Manual — part 94
SAT438D
2.
Install output shaft thrust needle bearing on bearing retainer.
SAT439D
3.
Install output shaft on transmission case.
SAT874DA
4.
Measure dimensions “
1
” and “
2
” at side cover and then cal-
culate dimension “A”.
I
Measure dimension “
1
” and “
2
” in at least two places
“A”: Distance between transmission case fitting surface
and adjusting shim mating surface
A =
1
−
2
2
: Height of gauge
SAT875DA
5.
Measure dimensions “
2
” and “
3
” and then calculate dimen-
sion “B”.
Measure “
2
” and “
3
” in at least two places.
“B”: Distance between the end of output shaft bearing
outer race and the side cover fitting surface of transmis-
sion case
B =
2
−
3
2
: Height of gauge
SAT440D
6.
Select proper thickness of adjusting shim so that output shaft
end play (clearance between side cover and output shaft bear-
ing) is within specifications.
Output shaft end play (A − B):
0 - 0.5 mm (0 - 0.020 in)
Output shaft end play adjusting shim:
Refer to SDS, AT-398.
7.
Install adjusting shim on output shaft bearing.
GI
MA
EM
LC
EC
FE
CL
MT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Adjustment (1) (Cont’d)
AT-373
SAT441D
8.
Apply locking sealant to transmission case as shown in illus-
tration.
SAT442D
9.
Install side cover on transmission case.
I
Apply locking sealant to the mating surface of transmis-
sion case.
SAT124E
10. Tighten side cover fixing bolts to specified torque.
I
Do not mix bolts A and B.
I
Always replace bolts A as they are self-sealing bolts.
SAT354D
Assembly (2)
NCAT0175
1.
Remove paper rolled around bearing retainer.
2.
Install thrust washer on bearing retainer.
I
Apply petroleum jelly to thrust washer.
SAT355D
3.
Install forward clutch assembly.
I
Align teeth of low & reverse brake drive plates before
installing.
I
Make sure that bearing retainer seal rings are not spread.
ASSEMBLY
Adjustment (1) (Cont’d)
AT-374
SAT356D
4.
Install thrust needle bearing on bearing retainer.
I
Apply petroleum jelly to thrust bearing.
I
Pay attention to direction of thrust needle bearing.
SAT357D
5.
Install thrust needle bearing on rear internal gear.
I
Apply petroleum jelly to thrust needle bearing.
I
Pay attention to direction of thrust needle bearing.
SAT358D
6.
Hold forward clutch hub and turn overrun clutch hub.
Check overrun clutch hub for directions of lock and unlock.
I
If not as shown in illustration, check installed direction of for-
ward one-way clutch.
SAT359D
7.
Install rear internal gear assembly.
I
Align teeth of forward clutch and overrun clutch drive
plate.
SAT360D
8.
Install needle bearing on rear planetary carrier.
I
Apply petroleum jelly to needle bearing.
I
Pay attention to direction of needle bearing.
GI
MA
EM
LC
EC
FE
CL
MT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Assembly (2) (Cont’d)
AT-375
SAT052D
9.
Install rear sun gear on rear planetary carrier.
I
Pay attention to direction of rear sun gear.
SAT362D
10. Install rear planetary carrier on transmission case.
SAT363D
11. Install thrust needle bearing on front planetary carrier.
I
Apply petroleum jelly to thrust needle bearing.
I
Pay attention to direction of thrust needle bearing.
SAT048D
12. Install low one-way clutch to front planetary carrier by turning
it in the direction of the arrow as shown.
13. While holding front planetary carrier, turn low one-way clutch.
Check low one-way clutch for correct directions of lock and
unlock.
SAT047D
14. Install front planetary carrier assembly on transmission case.
ASSEMBLY
Assembly (2) (Cont’d)
AT-376
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст