Infiniti G20 (P11). Manual — part 95
SAT046D
15. Install snap ring with screwdriver.
I
Forward clutch and bearings must be correctly installed
for snap ring to fit groove of transmission case.
SAT367D
16. Install needle bearing on front sun gear.
I
Apply petroleum jelly to needle bearing.
I
Pay attention to direction of needle bearing.
SAT368D
17. Install front sun gear on front planetary carrier.
SAT369D
18. Install needle bearing on front sun gear.
I
Apply petroleum jelly to needle bearing.
I
Pay attention to direction of needle bearing.
SAT370D
19. Install high clutch hub on front sun gear.
GI
MA
EM
LC
EC
FE
CL
MT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Assembly (2) (Cont’d)
AT-377
SAT371D
20. Install needle bearing on high clutch hub.
I
Apply petroleum jelly to needle bearing.
I
Pay attention to direction of needle bearing.
SAT372D
21. Remove paper rolled around input shaft.
22. Install input shaft assembly.
I
Align teeth of high clutch drive plates before installing.
SAT373D
23. Install reverse clutch assembly.
I
Align teeth of reverse clutch drive plates before installing.
Adjustment (2)
NCAT0176
When any parts listed below are replaced, adjust total end play and
reverse clutch end play.
Part name
Total end play
Reverse clutch
end play
Transmission case
I
I
Overrun clutch hub
I
I
Rear internal gear
I
I
Rear planetary carrier
I
I
Rear sun gear
I
I
Front planetary carrier
I
I
Front sun gear
I
I
High clutch hub
I
I
High clutch drum
I
I
Oil pump cover
I
I
Reverse clutch drum
—
I
ASSEMBLY
Assembly (2) (Cont’d)
AT-378
SAT374D
TOTAL END PLAY
NCAT0176S01
I
Measure clearance between reverse clutch drum and needle
bearing for oil pump cover.
I
Select proper thickness of bearing race so that end play is
within specifications.
SAT375D
1.
Measure dimensions “K” and “L” and then calculate dimension
“J”.
SAT376D
a.
Measure dimension “K”.
SAT377D
b.
Measure dimension “L”.
c.
Calculate dimension “J”.
“J”: Distance between oil pump fitting surface of trans-
mission case and needle bearing mating surface of high
clutch drum
J = K − L
SAT378D
2.
Measure dimension “M”.
a.
Place bearing race and needle bearing on oil pump assembly.
GI
MA
EM
LC
EC
FE
CL
MT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Adjustment (2) (Cont’d)
AT-379
SAT379D
b.
Measure dimension “M”.
“M”: Distance between transmission case fitting surface
and needle bearing on oil pump cover
“M
1
”: Indication of gauge
SAT443D
c.
Measure thickness of straightedge “t”.
M = M
1
− t
3.
Adjust total end play “T
3
”.
T
3
= J − M
Total end play “T
3
”:
0.25 - 0.55 mm (0.0098 - 0.0217 in)
I
Select proper thickness of bearing race so that total end play
is within specifications.
Bearing races: Refer to SDS, AT-399.
SAT380D
REVERSE CLUTCH END PLAY
NCAT0176S02
I
Measure clearance between oil pump cover and thrust washer
for reverse clutch drum.
I
Select proper thickness of thrust washer so that end play is
within specifications.
SAT381D
1.
Measure dimensions “O” and “P” and then calculate dimension
“N”.
ASSEMBLY
Adjustment (2) (Cont’d)
AT-380
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст