Infiniti QX4. Electrical System (2003 year). Manual — part 10
Wiring Diagram — WARN —
NBEL0309
MEL311Q
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING LAMPS
Wiring Diagram — WARN —
EL-149
MEL312Q
WARNING LAMPS
Wiring Diagram — WARN — (Cont’d)
EL-150
MEL313Q
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING LAMPS
Wiring Diagram — WARN — (Cont’d)
EL-151
MEL397R
WARNING LAMPS
Wiring Diagram — WARN — (Cont’d)
EL-152
MEL315Q
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING LAMPS
Wiring Diagram — WARN — (Cont’d)
EL-153
MEL316Q
WARNING LAMPS
Wiring Diagram — WARN — (Cont’d)
EL-154
MEL317Q
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING LAMPS
Wiring Diagram — WARN — (Cont’d)
EL-155
SEL062WA
Fuel Warning Lamp Sensor Check
NBEL0310
1.
Turn ignition switch “OFF”.
2.
Disconnect fuel level sensor unit harness connector B12.
3.
Connect a resistor (80
Ω
) between fuel tank gauge unit harness
connector terminals 2 and 3.
4.
Turn ignition switch “ON”.
The fuel warning lamp should come on.
NOTE:
ECM might store the 1st trip DTC P0180 during this inspection.
If the DTC is stored in ECM memory, erase the DTC after recon-
necting fuel tank gauge unit harness connector.
Refer to EC-72, “HOW TO ERASE EMISSION-RELATED DIAG-
NOSTIC INFORMATION”.
MEL425F
Electrical Components Inspection
NBEL0311
OIL PRESSURE SWITCH CHECK
NBEL0311S01
Oil pressure
kPa (kg/cm
2
, psi)
Continuity
Engine start
More than 10 - 20
(0.1 - 0.2, 1 - 3)
NO
Engine stop
Less than 10 - 20
(0.1 - 0.2, 1 - 3)
YES
Check the continuity between the terminals of oil pressure switch
and body ground.
SEL901F
DIODE CHECK
NBEL0311S02
쐌
Check continuity using an ohmmeter.
쐌
Diode is functioning properly if test results are as shown in the
figure at left.
쐌
Check diodes at the combination meter harness connector
instead of checking them on the combination meter assembly.
Refer to EL-149, “WARNING LAMP” wiring diagrams.
NOTE:
Specification may vary depending on the type of tester. Before
performing this inspection, be sure to refer to the instruction
manual for the tester to be used.
WARNING LAMPS
Fuel Warning Lamp Sensor Check
EL-156
Wiring Diagram — AT/IND —
NBEL0477
MEL398R
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
A/T INDICATOR
Wiring Diagram — AT/IND —
EL-157
MEL608P
A/T INDICATOR
Wiring Diagram — AT/IND — (Cont’d)
EL-158
Component Parts and Harness Connector
Location
NBEL0312
SEL673Y
System Description
NBEL0313
The warning chime is controlled by the smart entrance control unit.
The warning chime is located in the smart entrance control unit.
Power is supplied at all times
쐌
through 7.5A fuse [No. 24, located in fuse block (J/B)]
쐌
to smart entrance control unit terminal 49 and
쐌
to key switch terminal 2,
쐌
through 10A fuse (No. 61, located in the fuse and fusible link box)
쐌
to tail lamp relay terminals 1 and 3.
When the ignition switch in the ON or START position, power is supplied
쐌
through 7.5A fuse [No. 11, located in the fuse block (J/B)]
쐌
to smart entrance control unit terminal 27.
Ground is supplied
쐌
to smart entrance control unit terminals 43 and 64
쐌
through body grounds M77 and M111.
When a signal, or combination of signals, is received by the smart entrance control unit, the warning chime
will sound.
IGNITION KEY WARNING CHIME
NBEL0313S01
When the key in the ignition switch in the OFF position, and the driver’s door open, the warning chime will
sound. Power is supplied
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING CHIME
Component Parts and Harness Connector Location
EL-159
쐌
from key switch terminal 1
쐌
to smart entrance control unit terminal 25.
Ground is supplied
쐌
from front door switch LH terminal 1
쐌
to smart entrance control unit terminal 1.
Front door switch LH terminal 2 is grounded through body grounds B11, B22 and D210.
LIGHT WARNING CHIME
NBEL0313S02
When ignition switch OFF, driver’s door open, and lighting switch in 1ST or 2ND position, warning chime will
sound. Power is supplied.
쐌
from tail lamp relay terminal 2
쐌
to smart entrance control unit terminal 19 and 57.
Ground is supplied
쐌
from front door switch LH terminal 1
쐌
to smart entrance control unit terminal 1.
Front door switch LH terminal 2 is grounded through body grounds B11, B22 and D210.
SEAT BELT WARNING CHIME
NBEL0313S03
With ignition switch turned ON and seat belt unfastened (seat belt buckle switch ON), warning chime will sound
for approximately 6 seconds.
Ground is supplied
쐌
from seat belt buckle switch terminal 1
쐌
to smart entrance control unit terminal 28.
Seat belt switch terminal 2 is grounded through body grounds B11, B22 and D210.
WARNING CHIME
System Description (Cont’d)
EL-160
Wiring Diagram — CHIME —
NBEL0314
MEL319Q
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING CHIME
Wiring Diagram — CHIME —
EL-161
MEL610P
WARNING CHIME
Wiring Diagram — CHIME — (Cont’d)
EL-162
SEL670Y
CONSULT-II Inspection Procedure
=NBEL0315
“KEY WARN ALM”/“LIGHT WARN ALM”/“SEAT BELT
ALM”
NBEL0315S01
1.
Turn ignition switch “OFF”.
2.
Connect “CONSULT-II” and “CONSULT-II CONVERTER” to
the data link connector.
SKIA3098E
3.
Turn ignition switch “ON”.
4.
Touch “START (NISSAN BASED VHCL)”.
SEL398Y
5.
Touch “SMART ENTRANCE”.
If “SMART ENTRANCE” is not indicated, go to GI-42, “CON-
SULT-II Data Link Connector (DLC) Circuit”.
SEL023X
6.
Touch “KEY WARN ALM”, “LIGHT WARN ALM” or “SEAT BELT
ALM”.
SEL322W
7.
Select diagnosis mode.
“DATA MONITOR” and “ACTIVE TEST” are available for the
warning chime.
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING CHIME
CONSULT-II Inspection Procedure
EL-163
CONSULT-II Application Items
NBEL0316
“KEY WARNING ALARM”
NBEL0316S01
Data Monitor
NBEL0316S0101
Monitored Item
Description
IGN ON SW
Indicates [ON/OFF] condition of ignition switch.
KEY ON SW
Indicates [ON/OFF] condition of key switch.
DOOR SW DR
Indicates [ON/OFF] condition of front door switch LH.
Active Test
NBEL0316S0102
Test Item
Description
CHIME
This test is able to check key warning chime operation. Key warning chime sounds for 2
seconds after touching “ON” on CONSULT-II screen.
“LIGHT WARN ALM”
NBEL0316S02
Data Monitor
NBEL0316S0201
Monitored Item
Description
LIGHT SW 1ST
Indicates [ON/OFF] condition of lighting switch.
IGN ON SW
Indicates [ON/OFF] condition of ignition switch.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch LH.
Active Test
NBEL0316S0202
Test Item
Description
CHIME
This test is able to check light warning chime operation. Light warning chime sounds for 2
seconds after touching “ON” on CONSULT-II screen.
“SEAT BELT WARM ALM”
NBEL0316S03
Data Monitor
NBEL0316S0301
Monitored Item
Description
IGN ON SW
Indicates [ON/OFF] condition of ignition switch.
SEAT BELT SW
Indicates [ON/OFF] condition of seat belt switch.
Active Test
NBEL0316S0302
Test Item
Description
CHIME
This test is able to check seat belt warning chime operation. Seat belt warning chime
sounds for 2 seconds after touching “ON” on CONSULT-II screen.
WARNING CHIME
CONSULT-II Application Items
EL-164
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст