Volkswagen Golf / Golf GTI / Jetta. Manual — part 94
26-17
Coolant temperature must be at least 85
C,
display group 1, display zone 2.
Catalytic converter temperature must be
at least 380 C,
display group 46,
display zone 2.
No DTCs may be stored in DTC
memory:
Repair Manual, 2.8 Liter VR6 4V Fuel
Injection & Ignition, Engine Code(s): BDF,
Repair Group 01
Oxygen sensor aging before catalytic
converter is OK, checking:
Repair Manual, 2.8 Liter VR6 4V Fuel
Injection & Ignition, Engine Code(s): BDF,
Repair Group 24
Oxygen sensor aging after catalytic
converter is OK, checking:
Repair Manual, 2.8 Liter VR6 4V Fuel
Injection & Ignition, Engine Code(s): BDF,
Repair Group 24
Note:
The diagnosis will only be ended if the
oxygen sensor aging diagnosis before and
after catalytic converter is completed
successfully first.
Exhaust system components, servicing
26-18
Test sequence
- Connect V.A.G 1551 (or V.A.G 1552). Start
engine and select "Address word" 01 of engine
control module.
Repair Manual, 2.8 Liter VR6 4V Fuel Injection
& Ignition, Engine Code(s): BDF, Repair Group
01
Rapid data transfer
HELP
Select function XX
Indicated on display
- Press keys 0 and 4 for function "Initiate basic
setting" and confirm entry with Q key.
Basic setting
Input display group number XXX
Indicated on display
- Press keys 0, 0 and 1 for "Display group number
1" and confirm entry with Q key.
System in basic setting 1
1
2
3
4
Indicated on display: (1...4
display zones)
Only continue with the test when:
Coolant temperature is above 85 C -Display
zone 2-
Exhaust system components, servicing
26-19
- Change to display group 46 as
follows:
- Press C key.
Basic setting
Input display group number XXX
Indicated on display
- Press keys 0, 4 and 6 for "Display
group number 46" and confirm
entry with Q key.
System in basic setting 46
1
2
3
4
Indicated on display: (1...4
display
zones)
Only continue with the test when:
Note:
This process can take approx. 80
seconds.
- Depress brake pedal and hold.
- Depress accelerator down to wide
open throttle position.
Engine speed will be increased by
engine control module to approx.
2300 rpm.
Catalytic converter temperature
is above 380 C -Display zone
2-
- Hold brake pedal and accelerator
down until display in display zone
4 jumps from "Test OFF" to "Test
ON".
- Continue to hold brake pedal and
accelerator down until display
zone 4 displays specification "Cat.
B1 OK.".
Exhaust system components, servicing
26-20
- Release brake and accelerator pedals.
"Cat B1 OK." appears in display zone 4:
- Press
key.
- Press keys 0 and 6 for function "End output" and
confirm entry with Q key.
- Switch ignition off.
"CatB1 n.OK." appears in display zone 4:
- Press
key.
- Check DTC memory:
Repair Manual, 2.8 Liter VR6 4V Fuel Injection
& Ignition, Engine Code(s): BDF, Repair Group
01
- Read readiness code:
Repair Manual, 2.8 Liter VR6 4V Fuel Injection
& Ignition, Engine Code(s): BDF, Repair Group
01
Exhaust system components, servicing
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст