Volkswagen Golf / Golf GTI / Jetta. Manual — part 171
01-226
Display group 34 - Oxygen Sensor (O2S) control - Oxygen Sensor (O2S) aging
diagnosis of Oxygen Sensor (O2S) before Three Way Catalytic Converter (TWC)
Control module in function "04-Basic setting"
Vehicle stationary, engine running at increased idle speed (only with depressed
brake pedal and accelerator)
System in basic
setting 34
Indicated on display
xxxx
rpm
xxx.x
C
x.xx Text
1
2
3
4
Display zones
Specification Evaluation
Result of Oxygen Sensor
(O2S) before Three Way
Catalytic Converter (TWC)
aging test
(Test OFF / Test ON / B1
P1 OK. / B1 P1 n.OK.)
B1 P1 OK.
Page 01-
227
Dynamic factor of Oxygen Sensor
(O2S) before Three Way Catalytic
Converter (TWC)
1.00...2.50
---
Three Way Catalytic Converter (TWC)
temperature
min. 380.0 C
---
Engine speed
Approx. 2300
rpm
---
Note on display zone 2:
Value calculated from engine speed and engine load.
Measured value (data) blocks
01-227
Evaluation of display group 34, display zone 4 - Oxygen Sensor (O2S) diagnosis -
Oxygen Sensor (O2S) aging before Three Way Catalytic Converter (TWC)
Appears on display
Possible cause
Corrective action
Oxygen Sensor (O2S)
before Three Way
Catalytic Converter
(TWC) not OK.: "B1 P1
n.OK.
DTC stored in DTC
memory
- Check DTC memory
Page
01-23
, DTC memory, checking
and erasing
Oxygen Sensor
(O2S) faulty before
Three Way Catalytic
Converter (TWC)
- Perform a road test to remove
possible residue on Oxygen
Sensor (O2S) and repeat
check.
- Perform diagnosis again if
result is same:
- Check Oxygen Sensor (O2S)
and Oxygen Sensor (O2S)
control before Three Way
Catalytic Converter (TWC)
Page 24-131
Measured value (data) blocks
01-228
Display group 36 - Oxygen Sensor (O2S) control - Oxygen Sensor (O2S)
diagnosis after Three Way Catalytic Converter (TWC) (operational readiness)
Control module in function "04-Basic setting"
Engine running at idle
System in basic
setting 36
Indicated on
display
x.xxx
V
Text ---
---
1
2
3
4
Display zones
Specification
Evaluation
No display
---
---
No display
---
---
Result of operational readiness of
Oxygen Sensor (O2S) after
Three Way Catalytic Converter
(TWC)
(Test OFF / Test ON / B1 P2
OK. / B1 P2 n.OK.)
B1 P2 OK.
Page 01-230
Oxygen Sensor (O2S) voltage, Oxygen
Sensor (O2S) after Three Way Catalytic
Converter (TWC)
0.100...0.900 V
Page 01-229
Measured value (data) blocks
01-229
Evaluating display group 36, display zone 1 - Oxygen Sensor (O2S)
voltage,Oxygen Sensor (O2S) after Three Way Catalytic Converter (TWC)
Appears on
display
Possible cause
Corrective action
Constant 1.100
V
Short to positive via: Oxygen
Sensor (O2S), sensor wiring,
Ground (GND) wiring, Motronic
Engine Control Module (ECM) -
J220-
- Check basic voltage of
Oxygen Sensor (O2S) after
Three Way Catalytic
Converter (TWC)
Page
24-146
Constant 0.000
V
Short to Ground (GND) via:
Oxygen Sensor (O2S), sensor
wiring, Ground (GND) wiring,
Motronic Engine Control Module
(ECM) -J220-
- Check Oxygen Sensor
(O2S) wiring after Three
Way Catalytic Converter
(TWC)
Page 24-148
Constant
between
0.400...0.500 V
Wiring open circuit via: Oxygen
Sensor (O2S), sensor wiring,
Ground (GND) wiring, Motronic
Engine Control Module (ECM) -
J220-
Measured value (data) blocks
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст