Volkswagen Golf / Golf GTI / Jetta. Manual — part 172
01-230
Evaluating display group 36, display zone 2 - Diagnosis of Oxygen Sensor (O2S)
after Three Way Catalytic Converter (TWC)
Appears on display
Possible cause
Corrective action
Oxygen Sensor (O2S)
after Three Way
Catalytic Converter
(TWC) not OK.: "B1 P2
n.OK.
DTC stored in DTC
memory
- Check DTC memory
Page
01-23
, DTC memory, checking
and erasing
Oxygen Sensor
(O2S) after Three
Way Catalytic
Converter (TWC)
faulty
- Perform a road test to remove
possible contaminates on
Oxygen Sensor (O2S) and repeat
check.
- Perform diagnosis again if result
is same:
- Check Oxygen Sensor (O2S)
and Oxygen Sensor (O2S)
control after Three Way Catalytic
Converter (TWC)
Page 24-140
Measured value (data) blocks
01-231
Display group 41 - Oxygen Sensor (O2S) control - Oxygen Sensor (O2S) heating
Engine running at idle
Read measured
value block 41
Indicated on display
---
Text
xx.xx
k
Text
1
2
3
4
Display zones
Specification Evaluation
Oxygen Sensor (O2S)
heating after Three Way
Catalytic Converter (TWC)
(Htg.nC.OFF / Htg.nC.ON)
Htg.nC.ON
Htg.nC.OFF
sporadically
changing
---
Resistance of Oxygen Sensor
(O2S) heating after Three Way
Catalytic Converter (TWC)
0.00...25.00 k
---
Oxygen Sensor (O2S) heating before Three
Way Catalytic Converter (TWC)
(Htg.bC.OFF / Htg.bC.ON)
Htg.bC.ON
Htg.bC.OFF
sporadically
changing
---
No display
---
---
Note:
The Oxygen Sensor (O2S) heating may be switched on or off depending on the
operating conditions of the engine, therefore the display in display zones 2 or 4 may
show "Htg.b(a)C.ON" or alternating from "Htg.b(a)C.ON" to Htg.b(a)C.OFF".
Measured value (data) blocks
01-232
Display group 43 - Oxygen Sensor (O2S) control - Oxygen Sensor (O2S) aging
diagnosis of Oxygen Sensor (O2S) after Three Way Catalytic Converter (TWC)
Control module in function "04-Basic setting"
Vehicle stationary, engine running at increased idle speed (only with depressed
brake pedal and accelerator)
System in basic
setting 43
Indicated on display
xxxx
rpm
xxx.x
C
x.xxx
V
Text
1
2
3
4
Display zones
Specification Evaluation
Result of Oxygen Sensor
(O2S) after Three Way
Catalytic Converter (TWC)
aging test
(Test OFF / Test ON / B1
P2 OK. / B1 P2 n.OK.)
B1 P2 OK.
Page 01-
233
Oxygen Sensor (O2S) voltage
Oxygen Sensor (O2S) after
Three Way Catalytic Converter
(TWC)
0.100...0.900
V
Page 01-
229
Three Way Catalytic Converter (TWC)
temperature
min. 380.0 C
---
Engine speed
Approx. 2300
rpm
---
Note on display zone 2:
Value calculated from engine speed and engine load.
Measured value (data) blocks
01-233
Evaluation of display group 43, display zone 4 - Oxygen Sensor (O2S) diagnosis -
Oxygen Sensor (O2S) aging after Three Way Catalytic Converter (TWC)
Appears on display
Possible cause
Corrective action
Oxygen Sensor (O2S)
after Three Way
Catalytic Converter
(TWC) not OK.: "B1 P2
n.OK.
DTC stored in DTC
memory
- Check DTC memory
Page
01-23
, DTC memory, checking
and erasing
Oxygen Sensor
(O2S) after Three
Way Catalytic
Converter (TWC)
faulty
- Perform a road test to remove
possible contaminates on
Oxygen Sensor (O2S) and repeat
check.
- Perform diagnosis again if result
is same:
- Check Oxygen Sensor (O2S)
and Oxygen Sensor (O2S)
control after Three Way Catalytic
Converter (TWC)
Page 24-140
Measured value (data) blocks
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст