Volkswagen Golf / Golf GTI / Jetta. Manual — part 152
01-150
Electrical Wiring Diagrams,
Troubleshooting & Component
Locations
The main fuses must be OK.
The battery voltage must be at
least 11.5 V.
If the vehicle is equipped with air
conditioning, this must be
switched off.
Selector lever must be in
position "P" or "N" on vehicles
with an automatic transmission.
Exhaust system between Three
Way Catalytic Converter (TWC)
and cylinder head must be free
of leaks
Ignition switched on, engine not
running.
Fuel Pump (FP) relay -J17- must
be OK., checking:
The signal from Brake Light
Switch -F- and Brake Vacuum
Vent Valve Switch -F47- -F85-
must be OK., checking
Page
24-206
.
Engine Coolant Temperature
(ECT) must be 85...110 C
display group 4, display zone
3.
Intake Air Temperature (IAT)
less than 80 C display group
4, display zone 4.
Three Way Catalytic Converter
(TWC) temperature must be at
least 380 C
display group
34, display zone 2.
Readiness code
01-151
Work sequence
- Connect VAG 1551 scan tool (or VAG 1552).
Then switch ignition on and select Motronic
Engine Control Module (ECM) -J220- with the
"Address word" 01. (Connecting scan tool and
selecting Engine Control Module (ECM)
Page
01-12
).
Work step 1: Check DTC memory
Rapid data transfer
HELP
Select function XX
Indicated on display:
- Operate scan tool taking into account the
information on the display:
- Press buttons -0- and -2- for function "Check
DTC memory" and confirm entry with Q button.
X Diagnostic Trouble Codes (DTCs) detected!
The number of Diagnostic Trouble Codes (DTCs)
stored or "No DTC detected!" will be shown on the
display.
If a DTC is stored:
Readiness code
01-152
Repair Diagnostic Trouble Codes
(DTCs) printed out using DTC table:
SAE P0 codes
Page 01-
30
,
SAE P1 codes
Page 01-
58
,
SAE P2 codes
Page 01-
98
,
SAE P3 codes
Page 01-
99
.
If no DTC is stored:
- Press
button.
- Continue with work step 3
Work step 2: Erase DTC memory
Rapid data transfer
HELP
Select function XX
Indicated on display:
Note:
The readiness code is reset or
erased each time DTC memory is
erased.
- Press buttons -0- and -5- for
function "Erase DTC memory"
and confirm entry with -Q- button.
Rapid data transfer
DTC memory is erased!
Indicated on display:
Readiness code
01-153
Note:
If the ignition is switched off between
"Check DTC memory" and "Erase
DTC memory" the DTC memory will
not be erased.
- Press
button.
Work step 3: Adjust the Throttle
Valve Control Module -J338- to the
Motronic Engine Control Module
(ECM) -J220-
Rapid data transfer
HELP
Select function XX
Indicated on display:
- Press buttons -0- and -4- for
function "Initiate basic setting"
and confirm entry with -Q- button.
Basic setting
Input display group number XXX
Indicated on display:
- Press buttons -0-, -6- and -0- for
"Display group number 60" and
confirm entry with -Q- button.
System in basic setting 60
xxx.x %
xxx.x % x
ADP. runs
Indicated on display: (1 to 4
display zones)
- Check specifications in display
zones 3 and 4:
Display zone 3: 0 to 8
Display zone 4: ADP. runs, ADP.
OK.
System in basic setting 60
xxx %
xxx % 8
ADP. OK.
Indicated on display: (1 to 4
display zones)
Readiness code
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст