Volkswagen Golf / Golf GTI / Jetta. Manual — part 158
01-174
- Leave engine running at idle until display zone 4
displays:
Specification: "Syst. OK."
If "Syst.n.OK." appears in display zone 4:
- Press
button.
- Check DTC memory, repair Diagnostic Trouble
Codes (DTCs) if necessary and then erase DTC
memory
Page 01-23
, DTC memory, checking
and erasing.
- Read readiness code
Page 01-146
. If the
DTC memory has been erased or the Motronic
Engine Control Module (ECM) -J220- was
disconnected from battery (B+) positive, the
readiness code must be generated again
Page 01-149
.
If no DTC is stored:
- Press buttons -0- and -6- for function "End
output" and confirm entry with -Q- button.
- Switch off ignition.
- Check combi-valve:
Repair Manual, 2.8 Liter VR6 4V Engine
Mechanical, Engine Code(s): BDF; Repair Group
26
Readiness code
01-175
If "Syst. OK." appears in display zone 4:
- Press
button.
Work step 16: Read readiness code
- Read readiness code
Page 01-146
.
Readiness code
01-176
Readiness code, generating (overview)
Work steps 1 to 5:
Work step/
Diagnosis
Function/group
Test
prerequisites
Display
zone 1
Display
zone 2
Display
zone 3
1 Check DTC
memory
02/---
Ignition on
---
---
---
2 Erase DTC
memory
05/---
Ignition on
---
---
---
3
Adapting
Throttle
Valve
Control
Module
04/60
Ignition on
Throt.
valve
angle
angle
sensor 1
Throt.
valve
angle
angle
sensor 2
Learning
step
counter
Specification: 3...93 %
97...3 %
8
4 Requesting
temperature
08/4
Idle speed
Idle
speed
Voltage
supply for
Motronic
Engine
Control
Module
(ECM) -
J220-
Coolant
temperature
Specification: 640...720
rpm
11.5...15.0
V
85.0...110.0
C
5
Leak
diagnosis
04/071
Idle speed
Reed
condition
Text
Text
Specification:
Reed
open
---
Check END
Readiness code
01-177
Work steps 6 to 9:
Work step/
Diagnosis
Function/group
Test
prerequisites
Display
zone 1
Display
zone 2
Display
zone 3
6 Oxygen
Sensor
(O2S)
control
status
08/30
Idle speed
Before
Three
Way
Catalytic
Converter
(TWC)
After Three
Way
Catalytic
Converter
(TWC)
No display
Specification:
111
xxx
---
7 Oxygen
Sensor
(O2S)
before
Three
Way
Catalytic
Converter
(TWC)
(Oxygen
Sensor
(O2S)
aging)
04/34
Brakes
operated
Accelerator
in wide
openthrottle
position.
Engine
speed
Three Way
Catalytic
Converter
(TWC)
temperature
Dynamic
factor of
Oxygen
Sensor
(O2S)
before
Three Way
Catalytic
Converter
(TWC)
Specification:
Approx.
2300
rpm
Greater than
380 C
1.00...2.50
8
Fuel
supply
system
(part
load)
04/216
Brakes
operated
Accelerator
in wide
openthrottle
position.
Engine
speed
Oxygen
Sensor
(O2S)
before
Three Way
Catalytic
Converter
(TWC)
lower part
load
Oxygen
Sensor
(O2S)
before
Three Way
Catalytic
Converter
(TWC)
idle speed
Specification:
---
---
---
Readiness code
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст