Volkswagen Golf / Golf GTI / Jetta. Manual — part 82
20-48
Selector lever must be in position "P" or "N"
on models with an automatic transmission.
Fuel pump relay -J17- must be OK,
checking:
Electrical Wiring Diagrams, Troubleshooting &
Component Locations
No DTCs may be stored in DTC memory:
Repair Manual, 2.8 Liter VR6 4V Fuel Injection
& Ignition, Engine Code(s): BDF, Repair Group
01
Checking activation
- Check activation of LDP -V144- via output
Diagnostic Test Mode (DTM):
Repair Manual, 2.8 Liter VR6 4V Fuel Injection
& Ignition, Engine Code(s): BDF, Repair Group
01
If activation is OK:
- Perform functional check
Page 20-49
.
Evaporative Emissions (EVAP) system
20-49
Functional check
Test conditions
Throttle valve angle less than 4%,
display
group 3, display zone 3.
Coolant temperature must be 85...110 C
display group 4, display zone 3.
Intake air temperature less than 80 C,
display group 4, display zone 4.
Test sequence
- Connect V.A.G 1551 Scan Tool (or V.A.G 1552).
Start engine and select "Address word" 01 of
engine control module.
Repair Manual, 2.8 Liter VR6 4V Fuel Injection
& Ignition, Engine Code(s): BDF, Repair Group
01
Rapid data transfer
HELP
Select function XX
Indicated on display
- Press keys 0 and 4 for function "Initiate basic
setting" and confirm entry with Q key.
Basic setting
Input display group number XXX
Indicated on display
Evaporative Emissions (EVAP) system
20-50
- Press keys 0, 7 and 1 for "Display group number
71" and confirm entry with Q key.
Note:
The engine must not be loaded during this
diagnosis, if this occurs the diagnosis will be
interrupted and will not start again until the
engine is revved-up.
System in basic setting 71
1
2
3
4
Indicated on display (1...4
display zones)
If "Reed op." appears in display zone 1:
If the diagnosis is initiated by the engine control
module the display in display zone 4 jumps from
"Test OFF" to "Test ON".
Note:
If the display in display zone 4 jumps from "Test
ON" to "Test OFF" during the diagnosis, repeat the
diagnosis. When repeating the diagnosis test, the
diagnosis can take up to 60 seconds before the
display in display zone 4 jumps from "Test OFF" to
"Test ON".
- Open fuel tank filler cap briefly to release
pressure in fuel tank. This will close reed
contact.
Evaporative Emissions (EVAP) system
20-51
- Leave engine running at idling speed until
display zone 4 displays specification "Syst. OK.".
If "Sys. OK." appears in display zone 4:
- Press
key.
- Press keys 0 and 6 for function "End output" and
confirm entry with Q key.
- Switch ignition off.
If "Sm leak or La leak" appears in display zone 2
and "Sys. n.OK." appears in display zone 4:
- Press
key.
- Check DTC memory:
Repair Manual, 2.8 Liter VR6 4V Fuel Injection
& Ignition, Engine Code(s): BDF, Repair Group
01
- Read readiness code:
Repair Manual, 2.8 Liter VR6 4V Fuel Injection
& Ignition, Engine Code(s): BDF, Repair Group
01
Evaporative Emissions (EVAP) system
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст