Volkswagen Golf / Golf GTI / Jetta. Manual — part 139
01-135
If no electrical or wiring concerns are
found:
- Check wiring for open circuit
between test box and 3-pin
connector referring to Electrical
Wiring Diagrams
Terminal 1 and socket 80
Terminal 2 and socket 25
Wire resistance: max. 1.5
- Additionally check wire for short
to battery positive and Ground
(GND). Specification:
- Check wire for open circuit
between 3-pin connector terminal
3 and fuel pump relay -J17-
referring to Electrical Wiring
Diagrams.
Wire resistance: max. 1.5
- Replace Motronic Engine Control
Module (ECM) -J220-
Page 24-
173
.
- Check DTC memory, repair
Diagnostic Trouble Codes (DTCs)
if necessary and then erase DTC
memory
Page 01-23
, DTC
memory, checking and erasing.
- Erase learned values and adapt
Motronic Engine Control Module
(ECM) -J220- again
Page 24-
182
.
Output Diagnosis Test Mode (DTM)
01-136
- Read readiness code
Page 01-146
. If the
DTC memory has been erased or the Motronic
Engine Control Module (ECM) -J220- was
disconnected from battery (B+) positive, the
readiness code must be generated again
Page 01-149
.
7. Activating Camshaft Adjustment Valve 1
(exhaust) -N318-:
- Press
button.
Output Diagnosis Test Mode
17457 / Literature
Indicated on display of VAG 1551 scan tool or VAG
1552:
or
Output Diagnosis Test Mode
Camshaft Adjustment Valve 1 -N318-
Indicated on display of VAS 5051
Note:
The Camshaft Adjustment Valve 1 (exhaust) is
barely audible when operating.
- Press
button.
The Camshaft Adjustment Valve 1 (exhaust)
must click until the next Output Diagnostic Test
element is activated by pressing
button.
Output Diagnosis Test Mode (DTM)
01-137
If the valve does not click:
Note:
Mark connector and component
before pulling connector off.
- Disconnect 2-pin connector from
Camshaft Adjustment Valve 1
(exhaust) -N318- -2-.
LED flashes:
- Connect LED test light VAG 1527
to disconnected connector using
adapter cables from VAG 1594.
LED must flash (bright/darker)
- Press -C- button to abort output
Diagnosis Test Mode (DTM).
Output Diagnosis Test Mode (DTM)
01-138
Output Diagnosis Test Mode was aborted
Indicated on display:
Repair Manual, 2.8 Liter VR6 4V
Engine Mechanical, Engine Code(s):
BDF; Repair Group 15, Valve train,
servicing
Note:
The control housing is only replaced
complete with Valve -1- for camshaft
adjustment -N205- and Camshaft
Adjustment Valve 1 (exhaust) -N318-
.
LED does not flash:
- Switch off ignition.
- Replace engine control housing:
- Check DTC memory, repair
Diagnostic Trouble Codes (DTCs)
if necessary and then erase DTC
memory
Page 01-23
, DTC
memory, checking and erasing.
- Read readiness code
Page 01-
146
. If the DTC memory has
been erased or the Motronic
Engine Control Module (ECM) -
J220- was disconnected from
battery (B+) positive, the
readiness code must be
generated again
Page 01-149
.
- Press -C- button to abort output
Diagnosis Test Mode (DTM).
Output Diagnosis Test Mode was aborted
Indicated on display:
Repair Manual, Electrical
Equipment, Repair Group 92
- Switch off ignition.
- Remove wiper arms and cowl
panel:
Output Diagnosis Test Mode (DTM)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст