Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 810
– Remove the nuts -arrows- on the left and right side of the ve‐
hicle.
Vehicles with Level Control System Sensor
– Disconnect the connector -1- from the Left Front Level Control
System Sensor - G78- or Right Front Level Control Sensor -
G289- .
Continuation for all Vehicles
– Remove the clips -1 and 2- for the wiring harness -3- from the
subframe and the steering gear.
– Remove the steering gear bolts -1-.
– Pry the steering gear out of the subframe alignment sleeves.
– Place the -VAS6931- -1- under the subframe.
– Secure the subframe (refer to
⇒ “2.2 Subframe, Securing”, page 17
) and lower it approxi‐
mately 10 cm.
– Remove the expanding clip -arrow-.
– Lower the subframe using the -VAS6931- .
– Secure the subframe on the -VAS6931- .
– Secure the steering gear on the body.
Installing
Install in reverse order of removal while noting the following:
– Tighten nuts -arrows-.
Note
Tighten the nuts -arrows- in curb weight position. Refer to
⇒ “3.8.1 Wheel Bearing in Curb Weight, Lifting Vehicles with Coil
– For vehicles with a level control system sensor, perform the
basic setting for the wheel damping electronics using the
⇒ Vehicle diagnostic tester.
Tightening Specifications
♦ Refer to
⇒ “2.1 Overview - Subframe”, page 16
♦ Refer to
⇒ “2.1 Overview - Steering Column”, page 338
♦ Pendulum support bolts. Refer to ⇒ Rep. Gr. 10 ; Subframe
Mount; Overview - Subframe Mount .
♦ Noise insulation bolts. Refer to ⇒ Body Exterior; Rep. Gr. 66 ;
Noise Insulation; Overview - Noise Insulation .
♦ Exhaust system to subframe. Refer to ⇒ Rep. Gr. 26 ; Exhaust
Pipes/Mufflers; Overview - Muffler .
♦
If the steering wheel is still crooked after using the -T10486/1-
then an axle alignment is necessary. In this case the record it in
the vehicles axle alignment log.
2.5
Subframe with Steering Gear, Remov‐
ing and Installing
Special tools and workshop equipment required
♦ Puller - Ball Joint - T10187-
♦ Torque Wrench 1332 40-200Nm - VAG1332-
Removing
– Turn the steering wheel in the straight position and remove the
ignition key so that the steering wheel lock engages.
Vehicles with “Keyless Access” Keyless Locking and Starting
System
– Switch the ignition off and open the driver door so the steering
wheel lock engages.
Continuation for all Vehicles.
– Remove the bolts -1- and fold the footwell trim panel -2- in the
direction of the -arrow- into the vehicle interior.
– Remove the bolt -1- from the universal joint -2-. Then remove
the universal joint in direction of -arrow-.
Caution
If the universal joint is separated from the steering gear, the
following work cannot be performed:
♦ Connect the battery.
♦ Switching on the ignition
♦ Turning the steering gear
♦ Turning the steering column.
These points must be observed since performing these actions
could cause irreparable damage.
– Loosen the wheel bolts.
– Raise the vehicle.
– Remove the wheels.
– Remove the lower noise insulation. Refer to ⇒ Body Exterior;
Rep. Gr. 66 ; Noise Insulation; Overview - Noise Insulation .
– Remove the exhaust system bracket from the subframe
-arrows-.
– Remove the pendulum support bolts -1-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст