Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 349
2.3
Overview - Roof Grab Handle
Note
The overview illustration shows the left front roof grab handle. The illustration for the remaining roof grab handles
is identical.
1 - Roof Grab Handle Bracket
❑ Removing and instal‐
ling. Refer to
2 - Spacer
❑ Clipped to the roof grab
handle
❑ Before reinstalling, en‐
sure the correct installa‐
tion position, and cor‐
rect if necessary.
❑ Removing the spacer is
not permitted
3 - Headliner
❑ Removing and instal‐
ling. Refer to
4 - Roof Grab Handle
❑ Removing and instal‐
ling. Refer to
5 - Screw
❑ 4.5 Nm
❑ Quantity: 2
2.4
Screen Separator, Removing and Instal‐
ling
Removing
– Fold both rear seat backrests forward.
– Remove the screen separator -1- to the right from out of the
mounts -2- on the right 2/3 of the rear seat backrest.
Installing
– Position the screen separator -1- with the guides into the
mounts -2- on the right 2/3 of the rear seat backrest.
– Press the screen separator all the way to the left into the
mounts -2- on the right 2/3 of the rear seat backrest.
2.5
Screen Separator Mount, Removing
and Installing
Removing
– Remove the screen separator. Refer to
⇒ “2.4 Screen Separator, Removing and Installing”, page 44
.
– Remove the bolts -2-.
– Remove the insert -3- and mount -1- from the right 2/3 rear
seat backrest.
Installing
Install in reverse order of removal while paying attention to the
following:
Note
♦
Note the installation position of the insert -1- and the mount
-2-.
♦
Secure the mount -2- in the left threaded holes.
♦
Insert the tab on the insert -1- into the mount opening -2-.
♦
Remove the locking fluid from the bolt threads using a wire
brush. Then insert the bolts with locking compound. Refer to
the Parts Catalog.
♦
Remove the locking fluid from the bolt holes, for example using
a thread tap.
Tightening Specifications
♦ Refer to
2.6
Screen Separator Bracket, Removing
and Installing
Removing
– Remove the luggage compartment side trim panel. Refer to
⇒ “6.12.2 Luggage Compartment Side Trim Panel, Removing
and Installing, Wagon”, page 291
.
– Pull the seat belt webbing to the side and remove the bolts
-2-.
– Pull the screen separator bracket -1- out of the seat belt guide
-3- in direction of -arrow- and remove it.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “1.3 Overview - Outer Rear Three-Point Seat Belt”,
2.7
Screen Separator Mount, Removing
and Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
Removing
Screen Separator Mount without Rear Reading Lamp
Note
The removal and installation of the left rear screen separator
mount is described. The removal and installation of the other
screen separator mounts is identical.
– Remove the bolt -2-.
– Loosen the trim -1- with the screen separator mount from the
headliner at the bottom using the Trim Removal Wedge -
3409- in direction of -arrow A-.
– Then slightly guide the trim -1- with the screen separator
mount downward out of the headliner in direction of
-arrow B-.
– Then guide the screen separator mount with the trim upward
out of the headliner and remove it.
Note
For vehicles with a sunroof, the retaining tabs are turned 180° and
attached to the rear trim -1-. The removing and installing proce‐
dure for these screen separator mounts is identical.
Screen Separator Mount with Rear Reading Lamp
Note
The removal and installation of the left screen separator mount is
described. Removing and installing the right screen separator
mount is identical.
– Remove the Left Rear Reading Lamp - W11- . Refer to ⇒
Electrical Equipment; Rep. Gr. 96 ; Controls; Rear Interior
Lamp/Reading Lamp, Removing and Installing .
– Remove the bolt -2-.
– Release the retaining tabs -3- on the trim -1- and loosen the
trim from the headliner using the Trim Removal Wedge - 3409-
in direction of -arrow A-.
– Then guide the trim -1- with the screen separator mount for‐
ward out of the headliner in direction of -arrow B- and remove
it.
Installing
Install in reverse order of removal while paying attention to the
following:
Note
Make sure that the guide tab -arrow- on the screen separator
bracket is resting properly in the opening for the screen separator
mount -1-.
Tightening Specifications
♦ Refer to
⇒ “2.1 Overview - Screen Separator”, page 41
2.8
Sun Visor, Removing and Installing
Note
The removal and installation of the driver side sun visor is descri‐
bed. The removal and installation for the front passenger side is
identical.
Special tools and workshop equipment required
♦ Release Pliers - VAS6427-
Removing
– Pivot the sun visor forward.
– Using a flat-head screwdriver, carefully pry out the vanity mir‐
ror lighting -1- at the opening -arrow-.
– Disconnect the connector.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст