Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 348
– Put tape over the handle -2- to prevent it from getting dam‐
aged.
– Install the handle -2- on the parking brake lever -3-.
– Use the Assembly Tool - T10488- -1-.
– Mount the handle carefully on the parking brake lever -1- until
dimension -a- is reached.
Dimension -a-: 10 mm ± 1 mm
– Install the parking brake lever trim. Refer to
⇒ “1.20 Parking Brake Lever Trim, Removing and Installing”,
.
2
Equipment
⇒ “2.1 Overview - Screen Separator”, page 41
⇒ “2.2 Overview - Sun Visors”, page 43
⇒ “2.3 Overview - Roof Grab Handle”, page 44
⇒ “2.4 Screen Separator, Removing and Installing”, page 44
⇒ “2.5 Screen Separator Mount, Removing and Installing”,
page 45
⇒ “2.6 Screen Separator Bracket, Removing and Installing”, page
46
⇒ “2.7 Screen Separator Mount, Removing and Installing”,
page 46
⇒ “2.8 Sun Visor, Removing and Installing”, page 47
⇒ “2.9 Sun Visor Center Support, Removing and Installing”, page
49
⇒ “2.10 Roof Grab Handle, Removing and Installing”, page 50
⇒ “2.11 Roof Grab Handle Bracket, Removing and Installing”,
2.1
Overview - Screen Separator
1 - Screen Separator
❑ Removing and instal‐
ling. Refer to
2 - Screw
❑ 4.5 Nm
3 - Mount Trim
❑ Allocation. Refer to the
Parts Catalog.
❑ Removing and instal‐
ling. Refer to
.
4 - Screen Separator Mount
❑ Removing and instal‐
ling. Refer to
.
5 - Screw
❑ 4.5 Nm
❑ Quantity: 2
6 - Screw
❑ 1.5 Nm
7 - Mount Bracket
❑ Allocation. Refer to the
Parts Catalog.
❑ Removing
– Remove the headliner.
Refer to
⇒ “7.3.2 Headliner, Removing and Installing, Wagon”, page 301
– Remove the screws -5- and the mount bracket.
8 - Screw
❑ Refer to
⇒ “1.3 Overview - Outer Rear Three-Point Seat Belt”, page 88
9 - Screen Separator Bracket
❑ Removing and installing. Refer to
⇒ “2.6 Screen Separator Bracket, Removing and Installing”, page 46
10 - Rubber Grommet
❑ Slide over the screen separator bracket and insert into the luggage compartment side trim panel
11 - Mount
❑ On the right 2/3 rear seat backrest
❑ Removing and installing. Refer to
⇒ “2.5 Screen Separator Mount, Removing and Installing”, page 45
12 - Selector
❑ Removing and installing. Refer to
⇒ “2.5 Screen Separator Mount, Removing and Installing”, page 45
13 - Bolt
❑ 8 Nm
❑ Quantity: 2
Note
♦
Remove the locking fluid from
the bolt threads using a wire
brush. Then insert the bolts with
locking compound. Refer to the
Parts Catalog.
♦
Remove the locking fluid from
the bolt holes, for example using
a thread tap.
2.2
Overview - Sun Visors
Note
The overview illustration shows the driver side. The illustration for the front passenger side is identical.
1 - Sun Visor
❑ Removing and instal‐
ling. Refer to
.
2 - Sun Visor Mount
❑ Cannot be removed
from the sun visor
3 - Center Support
❑ For the sun visor
❑ Removing and instal‐
ling. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст