Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 73
3.3.2
Anti-Theft Alarm System Sensor -
G578- , Removing and Installing, Ver‐
sion with Four Screws
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
Caution
Risk of damaging the component surfaces.
♦ When positioning a prying tool, put commercially available
adhesive tape over the component in the visible area.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the Front Interior Lamp - WX1- . Refer to
⇒ “2.30 Front Interior Lamp/Reading Lamp, Removing and In‐
.
– Using the -3409- pry the cover -1- in the area of the -arrows-.
– Remove the screws -3-.
– Remove the roof module -2-.
– Disengage the connector and disconnect.
– Release the mounting tabs in the direction of the arrows
-A and B-.
– Remove the Anti-Theft Alarm System Sensor - G578- -1- from
the roof module.
– Release the mounting tabs in the direction of the
-arrows A and B-.
– Remove the individual sensor -1- from the roof module.
Installing
Install in the reverse order of removal while paying attention to
the following:
If the Anti-Theft Alarm System Sensor - G578- is being replaced,
then it must be adapted using the Vehicle Diagnostic Tester .
– Perform a function test.
Tightening Specifications
♦ Refer to
4
Driver Assistance Systems Front
Camera
⇒ “4.1 Driver Assistance Systems Front Camera, Removing and
4.1
Driver Assistance Systems Front Cam‐
era, Removing and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the mirror base cover. Refer to ⇒ Body Interior; Rep.
Gr. 68 ; Rearview Mirror; Overview - Rearview Mirror .
– Unclip the Driver Assistance Systems Front Camera - R242-
-2- in the direction of the -arrow A- from the clamps -1-.
– Remove the Driver Assistance Systems Front Camera - R242-
-1- in the direction of the -arrow B- from the bracket.
– Disconnect the connector -3-.
Installing
Install in the reverse order of removal while paying attention to
the following:
– Calibrate the Driver Assistance Systems Front Camera -
R242- . Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr.
44 ; Driver Assistance Systems Front Camera; Driver Assis‐
tance Systems Front Camera, Calibrating .
5
Cigarette Lighter and Socket
⇒ “5.1 Overview - Converter with Socket, 12 V-230 V”,
page 284
⇒ “5.2 Cigarette Lighter U1 , Removing and Installing”,
page 285
⇒ “5.3 Socket Illumination Bulb L42 , Removing and Installing”,
page 285
⇒ “5.4 Rear Cigarette Lighter Illumination Bulb L32 , Removing
5.1
Overview - Converter with Socket, 12 V-230 V
1 - Bracket
❑ To mount the Converter
with Socket, 12 V-230 V
- U13-
❑ Removing and instal‐
ling. Refer to
2 - Screw
❑ 2 Nm
❑ Quantity: 4
❑ To secure the Converter
with Socket, 12 V-230 V
- U13- to the bracket
3 - Bolt
❑ 9 Nm
❑ Quantity: 2
❑ To secure the bracket in
the side panel
4 - Converter with Socket, 12
V-230 V - U13-
❑ Must not be opened.
❑ No repairs on the con‐
nector, on the lines and
on the 230 V socket
❑ Removing and instal‐
ling. Refer to
5 - Connector
❑ 12-V input voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст