Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 72
2.32
Left/Right Front Reading Lamp Button -
E633- / -E634- , Removing and Installing
The Left Front Reading Lamp Button - E633- / Right Front Read‐
ing Lamp Button - E634- is a component of the Front Interior Lamp
- WX1- and cannot be replaced separately.
– Remove the Front Interior Lamp - WX1- . Refer to
⇒ “2.30 Front Interior Lamp/Reading Lamp, Removing and In‐
.
3
Anti-Theft Alarm System
⇒ “3.1 Overview - Interior Monitoring”, page 278
⇒ “3.2 Alarm Horn H12 , Removing and Installing”, page 279
⇒ “3.3 Anti-Theft Alarm System Sensor G578 , Removing and
3.1
Overview - Interior Monitoring
Note
The Sedan is shown. The Wagon is identical.
1 - Anti-Theft Alarm System
Sensor - G578-
❑ Removing and instal‐
ling. Refer to
❑ After replacing adjust.
Refer to
2 - Screw
❑ 1 Nm
❑ Quantity: 2 or 4, de‐
pending on version
3 - Cover
❑ Removing and instal‐
ling. Refer to
4 - Interior Monitoring And Ve‐
hicle Inclination Deactivation
Button - E616-
❑ Removing and instal‐
ling. Refer to
.
5 - Vehicle Electrical System Control Module - J519-
❑ With Central Locking and Anti-Theft Alarm System Antenna - R47-
❑ Overview. Refer to
⇒ “2.2 Overview - Control Modules”, page 298
6 - Alarm Horn - H12-
❑ Removing and installing. Refer to
⇒ “3.2 Alarm Horn H12 , Removing and Installing”, page 279
.
7 - Nut
❑ 9 Nm
❑ Quantity: 2
8 - Bracket
❑ Removing and installing. Refer to
⇒ “3.2 Alarm Horn H12 , Removing and Installing”, page 279
.
9 - Nut
❑ 6 Nm
3.2
Alarm Horn - H12- , Removing and In‐
stalling
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the plenum chamber cover. Refer to ⇒ Body Exterior;
Rep. Gr. 50 ; Bulkhead; Plenum Chamber Cover, Removing
and Installing .
– Remove the nuts -3-.
– Remove the alarm horn -1- with the bracket -4- from the ple‐
num chamber.
– Disconnect the connector -5-.
– If necessity remove the nut -2-.
– Remove the alarm horn -1- from the bracket -4-.
Installing
Install in the reverse order of removal while paying attention to
the following:
– Perform a function test.
Tightening Specifications
♦ Refer to
⇒ “3.1 Overview - Interior Monitoring”, page 278
3.3
Anti-Theft Alarm System Sensor -
G578- , Removing and Installing
⇒ “3.3.1 Anti-Theft Alarm System Sensor G578 , Removing and
Installing, Version with Two Screws”, page 279
⇒ “3.3.2 Anti-Theft Alarm System Sensor G578 , Removing and
Installing, Version with Four Screws”, page 281
3.3.1
Anti-Theft Alarm System Sensor -
G578- , Removing and Installing, Ver‐
sion with Two Screws
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the Front Interior Lamp - WX1- . Refer to
⇒ “2.30 Front Interior Lamp/Reading Lamp, Removing and In‐
– Remove the screws -2-.
– Remove the roof module -1- in the direction of the -arrow A-.
– Disengage the connector and disconnect.
– Release the mounting tabs in the direction of the
-arrows A and B-.
– Remove the Anti-Theft Alarm System Sensor - G578- -1- from
the roof module.
– Release the mounting tabs in the direction of the arrows
-A and B-.
– Remove the individual sensor -1- from the roof module.
Installing
Install in the reverse order of removal while paying attention to
the following:
If the Anti-Theft Alarm System Sensor - G578- is being replaced,
then it must be adapted using the Vehicle Diagnostic Tester .
– Perform a function test.
Tightening Specifications
♦ Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст