Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 988
5.2.2
Component Location Overview - Telephone System, Wagon
1 - Telephone Microphone -
R38-
❑ In the Front Interior
Lamp - W1-
❑ Removing and instal‐
ling. Refer to
2 - Information Electronics
Control Module 1 - J794-
❑ In the glove compart‐
ment
❑ Connector assignment.
Refer to ⇒ Wiring dia‐
grams, Troubleshooting
& Component locations.
❑ Removing and instal‐
ling. Refer to
.
3 - Mobile Communication 2-
Way Signal Amplifier - J984-
❑ Behind the luggage
compartment trim panel
on the right side
❑ Removing and instal‐
ling. Refer to
4 - Bolt
❑ 2 Nm
❑ Quantity: 2
5 - Storage Compartment with Cell Phone Interface - R265-
❑ Removing and installing. Refer to
⇒ “5.5 Storage Compartment with Cell Phone Interface R265 , Removing and Installing”, page 44
6 - Bolt
❑ 2 Nm
❑ Quantity: 2
5.3
Mobile Communication 2-Way Signal
Amplifier - J984- , Removing and Instal‐
ling
⇒ “5.3.1 Mobile Communication 2-Way Signal Amplifier J984 ,
Removing and Installing, Sedan”, page 42
⇒ “5.3.2 Mobile Communication 2-Way Signal Amplifier J984 ,
Removing and Installing, Wagon”, page 42
5.3.1
Mobile Communication 2-Way Signal
Amplifier - J984- , Removing and Instal‐
ling, Sedan
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the right luggage compartment side trim panel far
enough, until the Mobile Communication 2-Way Signal Ampli‐
fier - J984- is accessible. Refer to ⇒ Body Interior; Rep. Gr.
70 ; Luggage Compartment Trim Panels; Luggage Compart‐
ment Side Trim Panel, Removing and Installing .
– Push the tabs in direction of -arrow A-.
– Remove the Mobile Communication 2-Way Signal Amplifier -
J984- -1- from the bracket.
– Release and disconnect the connectors -2, 3 and 4- from the
Mobile Communication 2-Way Signal Amplifier - J984- -1-.
Installing
Install in reverse order of removal.
5.3.2
Mobile Communication 2-Way Signal
Amplifier - J984- , Removing and Instal‐
ling, Wagon
Removing
– Turn off the ignition and all electrical equipment.
– Then remove the ignition key, if equipped.
– Remove the right luggage compartment side trim panel far
enough, until the Mobile Communication 2-Way Signal Ampli‐
fier - J984- is accessible. Refer to ⇒ Body Interior; Rep. Gr.
70 ; Luggage Compartment Trim Panels; Luggage Compart‐
ment Side Trim Panel, Removing and Installing .
– If necessary, cut the cable tie on the bracket -3-.
– Push the catches -2 and 5- in the direction of the
-arrows A and B-.
– Remove the Mobile Communication 2-Way Signal Amplifier -
J984- -1- from the bracket.
– Release and disconnect the connectors -4- from the Mobile
Communication 2-Way Signal Amplifier - J984- -1-.
– Remove the bolts -2-.
– Remove the bracket for the Mobile Communication 2-Way
Signal Amplifier - J984- -1- from the sidewall.
– If installed, release and disconnect the connectors from the
Parking Heater Radio Receiver - R64- -3-.
– If installed, remove the Parking Heater Radio Receiver - R64-
from the bracket for the Mobile Communication 2-Way Signal
Amplifier - J984- .
Installing
Install in reverse order of removal. Note the following:
Tightening Specifications
♦ Refer to
⇒ “5.2.2 Component Location Overview - Telephone System,
5.4
Telephone Microphone - R38- , Remov‐
ing and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the Front Interior Lamp - W1- . Refer to ⇒ Electrical
Equipment; Rep. Gr. 96 ; Controls; Front Interior Lamp/Read‐
ing Lamp, Removing and Installing .
– Release the hooks -arrows-.
– Remove the Telephone Microphone - R38- -1- from the Front
Interior Lamp - W1- .
Installing
Install in reverse order of removal.
5.5
Storage Compartment with Cell Phone
Interface - R265- , Removing and Instal‐
ling
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
Caution
Risk of damaging the component surfaces.
♦ When positioning a prying tool, put commercially available
adhesive tape over the component in the visible area.
– Fold the center console armrest up.
– Pry off the cover -3- using the Trim Removal Wedge - 3409- .
– Remove the bolts -1-.
– Remove the mounting plate -2- from the storage compartment
in direction of -arrow A-
– Release and disconnect the connectors.
– Remove the coupler antenna on the back of the mounting plate
downward.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст