Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 986
– Remove the ignition key, if equipped.
The Left Antenna Module - R108- is located on the upper left side
of the rear lid.
– Remove the upper rear lid trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Luggage Compartment Trim Panels; Upper Rear
Lid Trim Panel, Removing and Installing .
– Release and disconnect the connectors -arrows- from the Left
Antenna Module - R108- .
– Loosen the screw -arrow-.
– Remove the screw with the metal clip and Left Antenna Mod‐
ule - R108- .
– Slide the Left Antenna Module - R108- in the direction of the
-arrow-.
– Remove the Left Antenna Module - R108- .
Installing
Install in reverse order of removal.
Tightening Specifications
Component
Tightening Specification
Screw to Left Antenna Module - R108-
2 Nm
3.4.2
Right Antenna Module - R109- , Remov‐
ing and Installing
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
The Right Antenna Module - R109- is located on the upper right
side of the rear lid.
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the rear lid upper trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Luggage Compartment Trim Panels; Upper Rear
Lid Trim Panel, Removing and Installing .
– Release and disconnect the connectors -arrows- from the
Right Antenna Module - R109- .
– Loosen the screw -arrow-.
– Remove the screw with the metal clip and Right Antenna Mod‐
ule - R109- .
– Slide the Right Antenna Module - R109- in the direction of the
-arrow-.
– Remove the Right Antenna Module - R109- .
Installing
Install in reverse order of removal.
Tightening Specifications
Component
Tightening Specification
Screw to Right Antenna Module - R109-
2 Nm
3.5
Roof Antenna, Removing and Installing
⇒ “3.5.1 Roof Antenna, Removing and Installing, Sedan”,
page 35
⇒ “3.5.2 Roof Antenna, Removing and Installing, Wagon”,
3.5.1
Roof Antenna, Removing and Installing,
Sedan
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
The back of the headliner must be lowered in order to remove the
Roof Antenna - RX5- .
The antenna wires are connected directly to the base of the Roof
Antenna - RX5- .
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Loosen the B-pillar upper trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Passenger Compartment Trim Panel; B-Pillar
Trim Panel, Removing and Installing .
– Remove the roof end strip. Refer to ⇒ Body Interior; Rep. Gr.
70 ; Roof Trim Panels; Roof End Strip, Removing and Instal‐
ling .
– Remove the C-pillar trim panel. Refer to ⇒ Body Interior; Rep.
Gr. 70 ; Passenger Compartment Trim Panel; C-Pillar Trim
Panel, Removing and Installing .
– Lower the back of the headliner.
– Release and disconnect the connectors -1- from the antenna
wires.
– Remove the bolt -3- with the clip.
– Remove the Roof Antenna - RX5- -2-.
Installing
Install in reverse order of removal. Note the following:
– Position the Roof Antenna - RX5- and press it down until it
latches.
Tightening Specifications
Component
Tightening Specification
Bolt -3- to Roof Antenna - RX5-
6 Nm
3.5.2
Roof Antenna, Removing and Installing,
Wagon
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
The back of the headliner must be lowered in order to remove the
Roof Antenna - RX5- .
The antenna wires are connected directly to the base of the Roof
Antenna - RX5- .
Removing
– Turn off the ignition and all electrical equipment.
– Then remove the ignition key, if equipped.
– Remove the C-pillar trim panel. Refer to ⇒ Body Interior; Rep.
Gr. 70 ; Passenger Compartment Trim Panel; C-Pillar Trim
Panel, Removing and Installing .
– Remove the roof end strip. Refer to ⇒ Body Interior; Rep. Gr.
70 ; Roof Trim Panels; Roof End Strip, Removing and Instal‐
ling .
– Remove the D-pillar trim panel. Refer to ⇒ Body Interior; Rep.
Gr. 70 ; Passenger Compartment Trim Panel; D-Pillar Trim
Panel, Removing and Installing .
– If installed, remove the screen separator mounting eye bolts,
but do not remove the mounting eyes. Refer to ⇒ Body Interior;
Rep. Gr. 68 ; Equipment; Screen Separator Bracket, Remov‐
ing and Installing .
– Lower the back of the headliner.
– Release and disconnect the connectors -1- from the antenna
wires.
– Remove the bolt -3- with the clip.
– Remove the Roof Antenna - RX5- -2- from the outside.
Installing
Install in reverse order of removal. Note the following:
– Position the Roof Antenna - RX5- and press it down until it
latches.
Tightening Specifications
Component
Tightening Specification
Bolt -3- to Roof Antenna - RX5-
6 Nm
3.6
Vehicle GPS Antennas, Removing and
Installing
⇒ “3.6.1 Vehicle GPS Antenna 1 R259 Removing and Installing,
GPS”, page 36
⇒ “3.6.2 Vehicle GPS Antenna 2 R260 , Removing and Installing,
3.6.1
Vehicle GPS Antenna 1 - R259- Remov‐
ing and Installing, GPS
The Vehicle GPS Antenna 1 - R259- is located behind the left rear
bumper cover.
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the rear bumper cover. Refer to ⇒ Body Exterior;
Rep. Gr. 63 ; Rear Bumper; Bumper Cover, Removing and
Installing .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст