Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 474
– Loosen the filter housing -arrow- approximately seven turns.
– Wait 10 seconds.
This way the fluid can flow from the filter housing back into the
transmission.
– Remove the filter housing and filter.
– Remove O-ring from filter housing.
Installing
Install in the reverse order of removal while noting the following:
– Clean thoroughly any areas on the transmission that get
stained with transmission fluid.
– Install the transmission fluid filter with the collar on the bottom
-arrow-.
– Install new O-ring on filter housing.
– Install and tighten the filter housing.
Install in reverse order of removal.
– Check the fluid level and fill if necessary. Refer to
⇒ “9.1 Transmission Fluid Level, Checking”, page 113
– Install the battery tray and the battery. Refer to ⇒ Electrical
Equipment; Rep. Gr. 27 ; Battery; Battery, Removing and In‐
stalling .
– Install the complete air filter housing:
♦ Gasoline engine. Refer to ⇒ Rep. Gr. 24 ; Air Filter; Air Filter
Housing, Removing and Installing .
♦ Diesel engine. Refer to ⇒ Rep. Gr. 23 ; Air Filter; Air Filter
Housing, Removing and Installing .
Tightening Specifications
♦ Filter housing. Refer to
9
Transmission Fluid
⇒ “9.1 Transmission Fluid Level, Checking”, page 113
⇒ “9.2 Transmission Fluid, Draining and Filling”, page 116
9.1
Transmission Fluid Level, Checking
Special tools and workshop equipment required
♦ Torque Wrench 5-50Nm - VAG1331-
♦ Used Oil Collection and Extraction Unit - SMN372500-
♦ Vehicle Diagnostic Tester
♦ Shop Crane - Drip Tray - VAS6208-
♦ Oil Filler - VAS6262A-
♦ Brake Line Tool Kit - Pipe Cutter - VAS6056/2-
♦ Also for some fluid containers Oil Filler - Adapter 6 -
VAS6262/6-
♦ Vehicle Diagnostic Tester
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Seal - Transmission Fluid Drain - and Check Plug
Note the Following Information:
♦ Use the ATF available as a replacement part. Refer to the
Parts Catalog.
♦ It is necessary to use the Oil Filler - Adapter 6 - VAS6262/6-
on some fluid containers.
♦ It may be necessary to shorten the bleed pipe on the Adapter
For Oil Filling - VAS6262A- . Refer to
.
Shorten the Bleed Pipe on the Adapter For Oil Filling - VAS6262A-
as Follows:
– Shorten the pipe to dimension -a-. This assures the pipe on
the Adapter For Oil Filling - VAS6262A- will not touch the bot‐
tom on some fluid containers.
Dimension -a- = 210 mm
Note
Dimension -a- is measured starting from the shaft (the green sur‐
face) on the Adapter For Oil Filling - VAS6262A- .
If dimension -a- is greater than 210 mm:
– Make a mark on the bleed pipe, dimension -a-, and cut it, with
for example the Brake Line Tool Kit - Pipe Cutter -
VAS6056/2- .
Requirements
♦ The vehicle is level and all hoist supports are the same height.
♦ Noise insulation is removed. Refer to ⇒ Body Exterior; Rep.
Gr. 66 ; Noise Insulation; Overview - Noise Insulation .
♦ Vehicle Diagnostic Tester is connected
♦ To begin working, the fluid temperature should not be higher
than 45 °C (113 °F).
♦ Test temperature: 35 ° to 45 °C (95 ° to 113 °F).
Checking
– Vehicle Diagnostic Tester Connect and identify the vehicle in
Guided Functions
.
– Select
DSG transmission
.
– Select
Check Fluid Level
.
Note
Let the transmission cool down if the fluid temperature is higher
than 45 °C (113 °F).
The engine is idling in neutral and the selector lever is in “P”.
– Move the Used Oil Collection and Extraction Unit -
SMN372500- or a Drip Tray under the transmission near the
transmission fluid drain and check plug.
– Remove the transmission fluid drain- and check plug -arrow-.
– Always replace the seal for the drain plug -arrow-.
Note
Even if the level of transmission fluid is too low, first a small
amount of transmission fluid will flow out of the overflow tube,
because it fills during operation.
– Let the excess fluid drain.
– Install the drain plug with a new seal as soon as all the fluid
has drained out (it starts to drip).
– If no transmission fluid comes out, then fill.
Adding
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст