Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 473
– Place the Used Oil Collection and Extraction Unit -
SMN372500- or Drip Tray under the transmission.
– Remove the Transmission fluid drain- and check plugs
-arrow- and drain the transmission fluid.
Caution
Do not start the engine if there is no transmission fluid in the
transmission.
A plastic overflow pipe is located in this hole (with 8 mm hex
socket head). Its length determines the fluid level in the trans‐
mission.
– Remove this overflow pipe and drain the remaining transmis‐
sion fluid.
– Reinstall the overflow pipe.
– Replace the bolt seal -arrow-.
In regard to »contaminated fluid«, also read the information on
changing the oil filter. Refer to
⇒ “8.3 Transmission Fluid Filter, Removing and Installing”,
.
– The Used Oil Collection and Extraction Unit - SMN372500- or
a Drip Tray remains under the transmission.
Caution
Fluid will leak out of the cover when the bolts are removed. Risk
of injury due to hot transmission fluid.
– The bolts -arrows- and remove the transmission fluid pump
cover -A-.
Note
Always replace the cover and the transmission fluid pump bolts
after removing.
– Remove the bolts -arrows-. Remove the transmission fluid
pump -1- from the alignment pin and the input shaft.
Remove the top bolt with the Wrench - Pump/Injector Long Reach
- T10054- .
Installing
– Install the transmission fluid pump input shaft -A- all the way
into the transmission. Turn the input shaft while doing this.
– Always use a new metal seal -B-.
• The two alignment pins -C- must be inside the transmission
housing.
– When positioning the transmission fluid pump, pay attention
to the driveshaft splines -A- and the correct seating on the
alignment pins -C-.
Different Transmission Fluid Pump Bolts -1-
All Four Bolts -arrows- with Flat Heads
Replace the bolts after removing them.
Tightening Specification
♦ 5 Nm + +90° (
1
/4 turn)
3 Bolts with Flat Head, Top Bolt -arrow- with Countersunk Head
Replace the bolts after removing them.
Tightening Specification
♦ Countersunk head bolt: 8 Nm without tightening angle (tighten
with the Wrench - Pump/Injector Long Reach - T10054- )
♦ Flat head screws: 8 Nm + 90° (
1
/4 turn)
– Mount the new transmission fluid pump cover -A-. Install the
new bolts -arrows- and tighten in a diagonal sequence in
stages.
Transmission does not have oil. »New« oil must now be added
and adjust to the correct oil level. Refer to
⇒ “9 Transmission Fluid”, page 113
– Install the left front wheel housing liner. Refer to ⇒ Body Ex‐
terior; Rep. Gr. 66 ; Wheel Housing Liner; Overview - Front
Wheel Housing Liner .
– Install the noise insulation. Refer to ⇒ Body Exterior; Rep. Gr.
66 ; Noise Insulation; Overview - Noise Insulation .
– Install the wheel. Refer to ⇒ Suspension, Wheels, Steering;
Rep. Gr. 44 ; Wheels, Tires; Wheel Bolts, Tightening Speci‐
fications .
Tightening Specifications
♦ Refer to
⇒ “1.1 Overview - Mechatronic”, page 28
♦ Transmission fluid pump to the transmission housing. Refer to
.
♦ Transmission fluid pump cover to transmission housing. Refer
to
⇒ Fig. ““Tightening Specification and Sequence of the Trans‐
mission Fluid Pump Cover -A-.”“ , page 30
.
8.3
Transmission Fluid Filter, Removing
and Installing
When to Change Transmission Fluid Filter
The transmission fluid filter does not need to be changed in every
case.
Do Not Replace the Filter If:
♦ The transmission fluid cooler or its O-rings were replaced and
no coolants has gotten into the transmission fluid.
♦ The selector shaft sealing ring was replaced.
♦ The flange seal was replaced.
♦ Leaking Mechatronic covers, DSG
®
clutch or transmission flu‐
id pump were replaced.
The Filter Must be Replaced If:
♦ The 60,000 km maintenance interval was reached.
♦ Coolant has entered the fluid.
♦ Metal shavings were found in the fluid.
♦ The clutch is burned or has a mechanical fault.
Note
General repair instructions. Refer to
⇒ “3 Repair Information”, page 5
.
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Filter - Transmission Fluid Filter
♦ O-ring - Filter Housing
Removing
– Move the selector lever into “P”.
– Remove the complete air filter housing:
♦ Vehicles with a gasoline engine. Refer to ⇒ Engine Mechan‐
ical, Fuel Injection and Ignition; Rep. Gr. 24 ; Air Filter; Air
Filter Housing, Removing and Installing
♦ Vehicles with a diesel engine. Refer to ⇒ Rep. Gr. 23 ; Air
Filter; Air Filter Housing, Removing and Installing
– Remove the battery with the battery tray. Refer to ⇒ Electrical
Equipment; Rep. Gr. 27 ; Battery; Battery Tray, Removing and
Installing .
Note
♦
A little bit of fluid remains inside the filter. This will drain out
once the filter is removed.
♦
Lay some cloths down near the filter before removing it.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст