Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 657
3.2
Crankshaft Dimensions
(Dimensions in mm)
Reconditioning
Dimension
1)
Crankshaft Bearing
Pin Diameter
Connecting Rod
Bearing Pin Diame‐
ter
Basic dimension
58.00
47.80
1)
The preparation of worn crankshafts is not provided.
3.3
Main Bearing Shells Allocation
The bearing shells are allocated to the cylinder block with the
correct thickness at the factory. Colored spots serve to identify
the bearing thicknesses.
The code letters on the lower contact surface or on the top of the
cylinder block identify which bearing shell and where it must be
mounted on the cylinder block (upper bearing shell).
The code letters on the crankshaft identify which bearing shells
and where they must be installed in the bearing cover (lower
bearing shell).
The first letter is for bearing cover one, the second for bearing
cover two, etc.
Cylinder Block Bearing Shell Identification:
Note
The cylinder block identification may be located either on the oil
pan sealing surface or on the top (transmission side) of the cyl‐
inder block.
The identification on the cylinder block is for the upper bearing
shell.
– Write down the letters and then use the table to find the color
identification.
Bearing Cap Bearing Shell Identification:
The identification on the crankshaft is for the lower bearing shell.
– Write down the letters and then use the table to find the color
identification.
S
=
Black
R
=
Red
G
=
Yellow
B
=
Blue
W
=
White
3.4
Crankshaft Needle Bearing, Replacing
Only for Vehicles Equipped with a Twin Clutch Transmission
Special tools and workshop equipment required
♦ Counter-support for example Puller - Kukko Counterstay -
22/1-
♦ Internal puller, for example Puller - Kukko Internal - 14-19mm
- 21/2-
♦ Bearing Installer - Bearing Press Piece - VW207C-
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Bearing - Crankshaft Needle
Conditions
• Always replace the needle bearing -arrow- after the engine
and transmission are separated.
• The front edges of the internal puller must not be broken off.
Remove Needle Bearing
– Remove the needle bearing -1- from the crankshaft -2- using
a standard internal puller such as the Puller - Kukko Internal -
14-19mm - 21/2- and counter support Puller - Kukko Counter‐
stay - 22/1- .
– The internal puller must be positioned behind the needle ring
-arrow-.
Installing
– Clean the bearing seat in the crankshaft and thinly coat with
grease.
– Drive the needle bearing into the crankshaft up to the instal‐
lation depth using the Bearing Installer - Bearing Press Piece
- VW207C- .
Installation Depth Dimension -a- = 2.0 mm
Note
If the needle bearing was unintentionally pushed in too deeply, it
must be replaced, because it will be damaged when it is removed
again.
3.5
Crankshaft, Measuring Axial Clearance
Special tools and workshop equipment required
♦ Dial Gauge Holder - VW387-
♦ Dial Gauge - 0-10mm - VAS6079-
Procedure
– Attach the Dial Gauge - 0-10mm - VAS6079- with the Dial
Gauge Holder - VW387- to the cylinder block and with ap‐
proximately 2 mm tension, set indicator against crankshaft
counterweight.
– Push the crankshaft against the dial gauge by hand and set
the dial gauge to “0”.
– Remove the crankshaft from the dial gauge and read the
measurement.
Axial clearance:
• New: 0.07 to 0.23 mm.
• Wear limit: 0.30 mm.
3.6
Crankshaft, Measuring Radial Clear‐
ance
Special tools and workshop equipment required
♦ Plastigage
®
Procedure
Note
♦
Do not interchange used bearings
♦
Bearing shells that are worn down to the nickel layer must be
replaced.
– Remove the crankshaft bearing cap and clean the bearing cap
and pins.
– Place Plastigage
®
over entire width of bearing journal or into
bearing shells.
• Plastigage
®
must rest in center of bearing shell.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст