Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 443
Left 1/3 Rear Seat Backrest
– Starting at the locking mechanism, pry off the clamping strip
-2- for the backrest cover using a screwdriver all around the
backrest frame -3- -arrow-.
– Remove the rear headrest guides. Refer to
⇒ “3.15 Headrest Guide, Removing and Installing”,
– Remove the backrest cover -1- and backrest cushion from the
backrest frame.
Rear Seat Backrest, 2/3 Right Without a Pass-Through
– Remove the rear center seat belt guide. Refer to
⇒ “1.4 Overview - Rear Center Three-Point Seat Belt”,
.
– Starting at the locking mechanism, pry off the clamping strip
-2- for the backrest cover using a screwdriver all around the
backrest frame -3- -arrow-.
– Remove the rear headrest guides. Refer to
⇒ “3.15 Headrest Guide, Removing and Installing”,
– Remove the backrest cover -1- and backrest cushion from the
backrest frame.
Rear Seat Backrest, 2/3 Right with a Pass-Through
– Remove the rear center seat belt guide. Refer to
⇒ “1.4 Overview - Rear Center Three-Point Seat Belt”,
– Remove the pass-through door with the rear center armrest.
Refer to
⇒ “3.12 Pass-Through Door, Removing and Installing”,
.
– Remove the pass-through cover frame. Refer to
⇒ “3.11 Pass-Through Cover Frame, Removing and Instal‐
– Starting at the locking mechanism, pry off the clamping strip
-2- for the backrest cover using a screwdriver all around the
backrest frame -3- -arrow-.
– Pry off the clamping strip -4- for the backrest cover with a
screwdriver from the opening for the pass-through.
– Remove the rear headrest guides. Refer to
⇒ “3.15 Headrest Guide, Removing and Installing”,
.
– Remove the backrest cover -1- and backrest cushion from the
backrest frame.
Installing
Install in reverse order of removal while paying attention to the
following:
– Flip the protective strip -1- over 180° toward the inside in di‐
rection of -arrow A-.
– Engage the protective strip in the groove on the backrest frame
in direction of -arrow B-.
2.5
Center Cushion, Removing and Instal‐
ling, Backrest with Pass-Through
Removing
– Fold the pass-through door forward.
– Release the tabs -1- with a screwdriver and push the center
cushion -2- until stop downward at the same time in direction
of -arrow A-.
– Slightly lift the upper center cushion in direction of -arrow B-
and at the same time disengage downward from the pass-
through door in direction of -arrow C-.
Installing
Install in reverse order of removal.
2.6
Bench Seat Cover and Cushion, Sepa‐
rating
Special tools and workshop equipment required
♦ Upholstery Clip Pliers - VAG1634-
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Upholstery Clips
Removing
– Remove the rear bench seat cover and the cushion. Refer to
⇒ “2.3 Bench Seat Cover and Padding, Removing and Instal‐
.
– Remove the seat cover -3- as far as possible from the seat
cushion -2-.
– Cut through the upholstery clips -1- with pliers.
– Separate the seat cover and the seat cushion.
Installing
Install in reverse order of removal while paying attention to the
following:
– After installing, make sure the seat cover is free of folds.
2.7
Rear Seat Backrest Cover and Cushion,
Separating
Special tools and workshop equipment required
♦ Upholstery Clip Pliers - VAG1634-
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Upholstery Clips
Removing
– Remove the backrest cover and backrest cushion from the
rear seat backrest. Refer to
⇒ “2.4 Rear Seat Backrest Cover and Cushion, Removing and
– Remove the backrest cover -2- as far as possible from the
backrest cushion -3-.
– Cut through the upholstery clips -1- with pliers.
Installing
Install in reverse order of removal while paying attention to the
following:
– After installing, make sure the seat cover is free of folds.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст