Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 442
– Separate the backrest cover and backrest cushion. Refer to
⇒ “1.7 Backrest Cover and Cushion, Separating”, page 410
– Cut the wire -3- directly from the old heating element -2-.
Note
The old heating elements remain on the backrest cushion -1- and
will be covered over by the new heating elements.
Installing
Install in reverse order of removal while paying attention to the
following:
– Guide the wire -3- through the wiring guide.
– Align the new heating elements on the backrest cushion while
not pulling off the protective film.
– Remove protective films from the heating elements in succes‐
sion, taking care not to damage the heating elements.
– Glue the heating elements so that they align with the old heat‐
ing elements and are free of wrinkles.
– Route the connections to the individual heating elements in
the base of the gaps.
Tightening Specifications
♦ Refer to
⇒ “1.2 Overview - Backrest Cover and Cushion”, page 403
♦ Refer to
⇒ “1.3 Overview - Seat Heating Element”, page 404
♦ Refer to
⇒ “2.2 Overview - Front Seat”, page 318
♦ Refer to
2
Rear Seat Covers and Cushions
⇒ “2.1 Overview - Bench Seat Cover and Cushion”, page 417
⇒ “2.2 Overview - Rear Seat Backrest Cover and Cushion”, page
418
⇒ “2.3 Bench Seat Cover and Padding, Removing and Installing”,
page 419
⇒ “2.4 Rear Seat Backrest Cover and Cushion, Removing and
Installing”, page 419
⇒ “2.5 Center Cushion, Removing and Installing, Backrest with
Pass-Through”, page 422
⇒ “2.6 Bench Seat Cover and Cushion, Separating”, page 422
⇒ “2.7 Rear Seat Backrest Cover and Cushion, Separating”, page
2.1
Overview - Bench Seat Cover and Cushion
1 - Seat Frame
2 - Seat Cushion
❑ Allocation. Refer to the
Parts Catalog.
❑ Seat cover and cushion,
removing and installing.
Refer to
❑ Separate the seat cover
from the seat cushion.
Refer to
.
3 - Upholstery Clip
❑ For attachment of the
seat cover to the seat
cushion
❑ Replace after removing
❑ Install at the same loca‐
tion with Upholstery Clip
Pliers - VAG1634- .
4 - Seat Cover
❑ Different equipment lev‐
els
❑ Allocation. Refer to the
Parts Catalog.
❑ Seat cover and cushion,
removing and installing.
Refer to
❑ Separate the seat cover from the seat cushion. Refer to
⇒ “2.6 Bench Seat Cover and Cushion, Separating”, page 422
❑ Make sure there are no folds after installing
5 - Molding
❑ Sewn into seat cover
❑ For engaging the seat cover in the seat frame
2.2
Overview - Rear Seat Backrest Cover and Cushion
1 - Backrest Cover
❑ Different equipment lev‐
els
❑ Allocation. Refer to the
Parts Catalog.
❑ Backrest cover and
cushion, removing and
installing. Refer to
❑ Backrest cover and
backrest cushion, sepa‐
rating. Refer to
❑ Make sure there are no
folds after installing
2 - Upholstery Clip
❑ For attachment of back‐
rest cover to backrest
cushion
❑ Replace after removing
❑ Install at the same loca‐
tion with Upholstery Clip
Pliers - VAG1634- .
3 - Backrest Cushion
❑ Allocation. Refer to the
Parts Catalog.
❑ Backrest cover and
cushion, removing and
installing. Refer to
Removing and Installing”, page 419
.
❑ Backrest cover and backrest cushion, separating. Refer to
⇒ “2.7 Rear Seat Backrest Cover and Cushion, Separating”, page 423
4 - Backrest Frame
5 - Clamping Strip
❑ Sewn into backrest cover
❑ For attaching the backrest cover on the backrest frame
2.3
Bench Seat Cover and Padding, Re‐
moving and Installing
Removing
– Remove the rear bench seat. Refer to
⇒ “3.7 Bench Seat/Single Seat, Removing and Installing”,
.
– Disengage the seat cover molding -3- around the seat frame.
– Disengage the seat cover molding -1- at the seat belt latch
openings.
– Remove the seat cover -2- with the seat cushion from the seat
frame.
Caution
Do not damage the seat cover.
♦ Do not pull on the seat cover. The seat cover can rip.
Installing
Install in reverse order of removal while paying attention to the
following:
– After installing, make sure the seat cover is free of folds.
2.4
Rear Seat Backrest Cover and Cushion,
Removing and Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
♦ Wedge Set - T10383-
Removing
– Remove the rear seat backrest. Refer to
⇒ “3.8 Rear Seat Backrest, Removing and Installing”,
.
– Remove the rear headrest. Refer to
⇒ “3.14 Headrest, Removing and Installing”, page 390
– Remove the locking mechanism trim. Refer to
⇒ “3.9 Locking Mechanism Trim, Removing and Installing”,
.
– Loosen the clips -2- from the backrest cover -1- near the inner
mounting pins.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст