Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 422
Caution
With 2-door vehicles pay attention that the seat outside the
vehicle is carefully moved in the end positions of the seat for‐
ward/back adjustment, there is a risk of damage.
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
♦ Airbag Lockout Adapter - VAS6282-
Removing
WARNING
Follow the General Safety Precautions when working with air‐
bags, belt tensioners and battery cut-out units (pyrotechnic
⇒ “1 Safety Precautions”, page 1
– Move the seat as far forward as possible using the forward/
back adjuster.
If the Driver Seat Forward/Back Adjustment Motor - V28- / Front
Passenger Seat Forward/Back Adjustment Motor - V31- is faulty,
it is not possible to adjust a power front seat using the Driver Seat
Adjustment Control Head - E470- / Front Passenger Seat Adjust‐
ment Control Head - E471- . In this case, perform the appropriate
procedure. Refer to
⇒ “2.11 Front Seat, Removing with Faulty Driver/Front Passenger
Seat Forward/Back Adjustment Motor V28 / V31 ”, page 339
.
– Remove the bolts -3 and 4-.
– Move the seat as far back as possible using the forward/back
adjuster.
– Remove the bolts -1 and 2-.
– Disconnect the battery. Refer to ⇒ Electrical Equipment; Rep.
Gr. 27 ; Battery; Battery, Disconnecting and Connecting .
– Tilt the seat back.
– Open the cover in the carpet.
– Depending on the vehicle equipment level, release and re‐
move the wiring harnesses from the seat at the connector
station.
– Connect the airbag adapter. Refer to
⇒ “2.12 Airbag Adapter, Connecting and Disconnecting”, page
Caution
If seat is to be lifted out or transported out of the vehicle, it must
not be grasped by the attachments, for example, seat belt
latch, lever for seat fore/aft adjustment, lever for seat height
adjustment or seat trim panels in order to prevent damage.
– Protect the attachments from damage using suitable materi‐
als.
– Reach between the backrest and seat cushion with the right
hand. Grab the front of the seat cushion with the left hand and
lift the seat out of the vehicle.
Installing
Note
Before installing the seat in the vehicle, make sure that the two
identical locking pins -1- are at the bottom in both seat rails.
– Lift seat through the front door and into the vehicle.
– First position the front seat.
– Guide the seat into the centering pins.
– Attach the seat with the front bolt -1- in the vehicle.
– Attach the seat with the front bolt -2- in the vehicle.
– Move the seat forward as far as possible.
– Attach the seat with the rear bolt -3- in the vehicle.
– Attach the seat with the rear bolt -4- in the vehicle.
WARNING
When installing the seat, if a thread in the seat crossmember
mounting plate was damaged, a reworking of the damaged
thread is forbidden. In this case, the seat crossmember mount‐
ing plate must be replaced.
If there is damage to threads in the seat crossmember mounting
plate:
– Replace the affected seat crossmember mounting plate. Refer
to ⇒ Body Repair; Rep. Gr. 51 .
– Remove the Airbag Lockout Adapter - VAS 6282- .
– Attach the thorax airbag wiring harness to the connector sta‐
tion.
– Depending on the vehicle equipment level, engage the wiring
harnesses in the coupling station.
– Close the cover in the carpet.
– Switch the ignition on.
WARNING
Make sure that no persons are in the vehicle.
– Connect the battery. Refer to ⇒ Electrical Equipment; Rep.
Gr. 27 ; Battery; Battery, Disconnecting and Connecting .
Note
If the Airbag Indicator Lamp - K75- signals a fault after installing,
check the DTC memory, erase it and check it again use the Ve‐
hicle Diagnostic Tester .
Tightening Specifications
♦ Refer to
⇒ “2.2 Overview - Front Seat”, page 318
2.11
Front Seat, Removing with Faulty Driv‐
er/Front Passenger Seat Forward/Back
Adjustment Motor -V28- / -V31-
Driver Seat Forward/Back Adjustment Motor - V28- / Front Pas‐
senger Seat Forward/Back Adjustment Motor - V31- , Checking
– Move the front seat into its highest position.
Note
To avoid unnecessary repair costs, check the Driver Seat For‐
ward/Back Adjustment Motor - V28- / Front Passenger Seat For‐
ward/Back Adjustment Motor - V31- before removing the front
seat.
– Check the Driver Seat Forward/Back Adjustment Motor -
V28- / Front Passenger Seat Forward/Back Adjustment Motor
- V31- using the Vehicle Diagnostic Tester .
– Replace the seat pan lower frame with the faulty Driver Seat
Forward/Back Adjustment Motor - V28- / Front Passenger
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст