Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 580
9 - Transmission Bracket
10 - Transmission Mount
❑ Check the adjustment. Refer to ⇒ Engine Mechanical, Fuel Injection and Ignition; Rep. Gr. 10 ; Subframe
Mount; Subframe Mount, Checking Adjustment
❑ Adjusting. Refer to ⇒ Engine Mechanical, Fuel Injection and Ignition; Rep. Gr. 10 ; Subframe Mount;
Subframe Mount, Adjusting
11 - Bolt
❑ Transmission mount to chassis
❑ Refer to ⇒ Engine Mechanical, Fuel Injection and Ignition; Rep. Gr. 10 ; Subframe Mount; Overview -
Subframe Mount .
12 - Bolt
❑ 60 Nm +90°
❑ Replace after removing
❑ Tightening sequence. Refer to
⇒ Fig. ““Attaching the Transmission Mount to the Transmission Bracket”“ , page 88
❑ Transmission mount to transmission bracket
Attaching the Transmission Mount to the Transmission Bracket
– Replace the bolts -arrows-.
– Tighten all bolts hand-tight.
– Tighten the bolt to the tightening specification.
Transmission Support to Transmission Bracket and Transmission
– Replace the bolts -arrows-.
– Tighten both bolts -arrows- hand-tight at first.
– Tighten the bolt to the tightening specification.
Transmission Bracket -A- to Transmission.
– Replace the bolts -arrows-.
– Tighten all bolts hand-tight.
– Tighten the bolt to the tightening specification.
4
Transmission, Transporting
Special tools and workshop equipment required
♦ Transmission Support Jig - 3336-
♦ Shop Crane - VAS6100-
– Attach the Transmission Support Jig - 3336- to the clutch
housing.
– Move the support arm on the sliding bar using the locking bolt
-arrow-.
Number of visible holes = 5.
– Lift the transmission using the Shop Crane - VAS6100- and
the Transmission Support Jig - 3336- .
– Set the transmission down, for example, into the transport
container.
5
Transmission, Disassembling and
Assembling
⇒ “5.1 Schematic Overview - Transmission”, page 90
⇒ “5.2 Overview - Transmission”, page 92
⇒ “5.3 Overview - Transmission Housing Cover and 5th Gear”,
page 93
⇒ “5.4 Overview - Transmission Housing and Selector Mecha‐
nism”, page 95
⇒ “5.5 Overview - Shift Unit”, page 96
⇒ “5.6 Overview - Input Shaft, Output Shafts, Differential, Gear‐
shift Rods”, page 97
⇒ “5.7 Overview - Shift Forks”, page 98
⇒ “5.8 Shift Unit, Servicing”, page 99
⇒ “5.9 Shift Forks, Servicing”, page 100
⇒ “5.10 Transmission Housing Cover and 5th Gear, Removing”,
page 101
⇒ “5.11 Transmission, Disassembling and Assembling”,
page 105
⇒ “5.12 Transmission Housing Cover and 5th Gear, Installing”,
5.1
Schematic Overview - Transmission
1 - 1st Gear
2 - 2nd Gear
3 - 3rd Gear
4 - 4th Gear
5 - 5th Gear
6 - Transmission Housing Cov‐
er
7 - Transmission Housing
8 - Selector Mechanism
❑ (Shift forks)
9 - Reverse Drive Gear
10 - Clutch Housing
11 - Input Shaft
12 - Output Shaft
13 - Differential
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст