Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 372
Tightening Specifications
♦ Refer to
⇒ “5.1 Overview - Driver Side Airbag”, page 131
5.3
Airbag Connector, Replacing
Removing
WARNING
Observe the safety precautions for pyrotechnical components.
Refer
to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”, page
.
– Remove the driver side airbag. Refer to
⇒ “5.2 Airbag Unit with Igniter, Removing and Installing”, page
.
Equipment Levels: Steering Wheel without Multifunction
WARNING
Before handling pyrotechnic components (for example, dis‐
connecting the connector), the person handling it must “dis‐
charge static electricity”. This can be done by touching the door
striker pin, for example.
– Release the connector lock -2- using a small screwdriver in
direction of -arrow- and remove the connector -1- from the
Driver Airbag Igniter - N95- .
– Disconnect the connectors from the wiring harness -1-.
– Disengage the wiring harness at the brackets and remove
from the driver side airbag -2-.
Equipment Levels: Steering Wheel with Multifunction
WARNING
Before handling pyrotechnic components (for example, dis‐
connecting the connector), the person handling it must “dis‐
charge static electricity”. This can be done by touching the door
striker pin, for example.
– Release the connector lock -2- using a small screwdriver in
direction of -arrow- and remove the connector -1- from the
Driver Airbag Igniter - N95- .
– Disconnect the connectors from the wiring harness -1-.
– Disengage the wiring harness at the brackets and remove
from the driver side airbag -2-.
Installing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
♦ Before handling pyrotechnic components (for example,
connecting the connector), the person handling it must
“discharge static electricity”. This can be done by touching
the door striker pin, for example.
– Connect the connector -1- to the airbag igniter in direction of
-arrow A-.
– Install the connector locking mechanism -2- in direction of
-arrow B-. While doing this, the connector is pushed into the
airbag igniter and locks into place.
Installation is performed in reverse order of removal, while noting
the following:
Note
Make sure the connectors are pushed in all the way and that they
engage audibly.
Tightening Specifications
♦ Refer to
6
Front Passenger Airbag
⇒ “6.1 Overview - Front Passenger Airbag”, page 138
⇒ “6.2 Front Passenger Airbag Unit with Igniter, Removing and
Installing”, page 139
⇒ “6.4 Front Passenger Airbag -Disabled- Indicator Lamp K145 ,
Removing and Installing”, page 142
6.1
Overview - Front Passenger Airbag
1 - Connector
❑ Depending on the mar‐
ket, one connector (sin‐
gle-stage airbag) or two
connectors (dual-stage
airbag)
❑ Single-stage airbag with
one connector for Front
Passenger Airbag Ignit‐
er 1 - N131-
❑ Dual-stage airbag with
two connectors for Front
Passenger Airbag Ignit‐
er 1 - N131- and Front
Passenger Airbag Ignit‐
er 2 - N132-
2 - Screws
❑ 8 Nm
❑ Quantity: 2
❑ Clean before reinstal‐
ling
❑ Insert with locking com‐
pound. Refer to the
Parts Catalog.
3 - Instrument Panel
❑ Replace the instrument
panel after an airbag
has deployed. Refer to
4 - Screws
❑ 8 Nm
❑ Quantity: 2
❑ Clean before reinstal‐
ling
❑ Insert with locking compound. Refer to the Parts Catalog.
5 - Front Passenger Airbag
❑ Depending on the market, single- or dual-stage
❑ Single-stage: with Front Passenger Airbag Igniter 1 - N131-
❑ Dual-stage: with Front Passenger Airbag Igniter 1 - N131- and Front Passenger Airbag Igniter 2 - N132-
WARNING
♦
Observe the safety pre‐
cautions for pyrotechni‐
cal components. Refer to
♦
Observe the allocation of
the airbag unit for the in‐
strument panel. Refer to
the Parts Catalog.
❑ Locking and activating possible with key switch
❑ Removing and installing. Refer to
⇒ “6.2 Front Passenger Airbag Unit with Igniter, Removing and Installing”, page 139
6.2
Front Passenger Airbag Unit with Ignit‐
er, Removing and Installing
Removing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
♦ Observe the disposal regulations for pyrotechnical com‐
ponents. Refer to
⇒ “1.3 Airbag, Belt Tensioner and Battery Cut-Out Units,
Storing, Transporting and Disposing (Pyrotechnic Com‐
♦ Observe the allocation of the airbag unit for the instrument
panel. Refer to the Parts Catalog.
– Disconnect the battery ground cable with the ignition turned
on. Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery;
Battery, Disconnecting and Connecting .
– Remove the glove compartment. Refer to
⇒ “1.17 Glove Compartment, Removing and Installing”,
WARNING
Before handling pyrotechnic components (for example, dis‐
connecting the connector), the person handling it must “dis‐
charge static electricity”. This can be done by touching the door
striker pin, for example.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст