Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 371
7 - Steering Wheel with Multifunction
❑ Equipment levels
❑ Overview. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 48 ; Steering Wheel; Overview - Steering
Wheel .
8 - Wiring Harness with Multifunction
❑ For Driver Airbag Igniter - N95-
❑ Replacing. Refer to
⇒ “5.3 Airbag Connector, Replacing”, page 136
.
❑ Press in to secure in the pockets on the steering wheel.
9 - Driver Side Airbag
❑ With Driver Airbag Igniter - N95-
WARNING
Observe the safety pre‐
cautions for pyrotechni‐
cal components. Refer to
.
❑ Removing and installing. Refer to
⇒ “5.2 Airbag Unit with Igniter, Removing and Installing”, page 132
10 - Screw
❑ Tightening specification. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 48 ; Steering Wheel;
Overview - Steering Wheel .
5.2
Airbag Unit with Igniter, Removing and
Installing
Special tools and workshop equipment required
♦ TORX® screwdriver T25, approximately 100 mm long, com‐
mercially available
Removing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
.
♦ Observe the disposal regulations for pyrotechnical com‐
ponents. Refer to
⇒ “1.3 Airbag, Belt Tensioner and Battery Cut-Out Units,
Storing, Transporting and Disposing (Pyrotechnic Com‐
.
– Position the steering wheel as far back and down as possible.
– Use the full adjustment range of the steering column adjuster.
– Remove the upper steering column trim. Refer to
⇒ “1.11 Upper Steering Column Trim Panel, Removing and
– Turn the steering wheel so the opening on the rear side of it
faces upward.
– Releases the locking bracket -1- for the driver side airbag -2-
in direction of -arrows-. Use a T25 TORX® screwdriver, ap‐
proximately 100 mm long.
Note
Electrical wires can be damaged with a flat-head screwdriver.
– Turn the steering wheel 180° and repeat the procedure on the
opposite side.
– Bring the steering wheel back into the center (wheels are
straight).
– Disconnect the battery ground cable with the ignition turned
on. Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery;
Battery, Disconnecting and Connecting .
WARNING
Before handling pyrotechnic components (for example, dis‐
connecting the connector), the person handling it must “dis‐
charge static electricity”. This can be done by touching the door
striker pin, for example.
– Remove the driver side airbag -3- from the steering wheel
slightly.
– Pull out the connector lock -2- -arrow- and press it down, dis‐
connect the connector -1-.
– Vehicles with multifunction steering wheel: Disconnect the
connector.
WARNING
Lay airbag unit so padding faces upward.
Installing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
.
♦ Before handling pyrotechnic components (for example,
connecting the connector), the person handling it must
“discharge static electricity”. This can be done by touching
the door striker pin, for example.
Install in reverse order of removal while paying attention to the
following:
Note
♦
Make sure the connectors are pushed in all the way and that
they engage audibly.
♦
Make sure the wires are not pinched.
– Connect the connector.
– Press in the connector to secure it in the pockets on the steer‐
ing wheel.
– Position the driver side airbag -1- in the steering wheel and
press on the edge with both hands until it locks into place.
WARNING
The ignition must be on when connecting the battery. If pyro‐
technic components (for example, airbag, belt tensioner) are
not repaired correctly, they may deploy unintentionally after
connecting battery. There must not be anyone inside the ve‐
hicle when connecting the battery.
– Connect the battery ground cable with the ignition turned on.
Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery; Bat‐
tery, Disconnecting and Connecting .
WARNING
If the ignition is not switched on after the battery is reconnected
- “indicator lamps in the instrument cluster do not light up” - the
ignition (key/button) may only be switched on when the driver
seat is positioned all the way back.
– Check and erase the airbag control module DTC memory be‐
cause faults can be stored from when the connectors are
disconnected use the Vehicle Diagnostic Tester .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст