Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 331
9.3.2
Front Emblem, Removing and Installing, Model Name GTI
Removing
– Remove the radiator grille. Refer to
⇒ “1.2 Radiator Grille, Removing and Installing”, page 396
.
– Release the hooks on the back -3- using a screwdriver in di‐
rection of -arrows-.
– Pull the model name emblem -1- from the radiator grille -2-.
Installing
– Press the model name emblem -1- on the radiator grille -2-
until the hooks -3- engage audibly.
– Install the radiator grille. Refer to
⇒ “1.2 Radiator Grille, Removing and Installing”, page 396
.
9.4
Rear Emblem, Removing and Installing
Note
The brand emblem cannot be removed without damaging it.
Removing
– Pry the brand emblem -1- carefully with a screwdriver -3- in
the direction of -arrow A- from the swiveling emblem -2- in di‐
rection of -arrow B-.
Installing
– Press the brand emblem -1- onto the swiveling emblem -2-
until it engages audibly.
9.5
Name Badges, Removing and Installing
Special tools and workshop equipment required
♦ Wiring Harness Repair Set - Hot Air Blower - VAS1978/14A-
♦ Adhesive Strip Remover - VAS6349-
♦ Adhesive Remover - D 002 000 10-
Assembly Instructions
♦ Warm the name badges or emblem before removing using a
Wiring Harness Repair Set - Hot Air Blower - VAS1978/14A- .
♦ When a name badge or emblem is removed and installed, use
only the Adhesive Remover - D 002 000 10- to remove the
adhesive residue.
♦ If necessary, remove any adhesive residue left by the tape
using Adhesive Strip Remover - VAS6349- .
♦ Make sure the adhesive surfaces are free of dust and grease.
♦ Attach the name badges or emblems immediately after clean‐
ing.
♦ Only remove the protective film right before assembly.
♦ The temperature must be approximately 21 °C (69.8 °F).
♦ It is not possible to remove the bonded name badges or em‐
blems without damaging them.
10
Trailer Hitch
⇒ “10.1 Overview - Trailer Hitch”, page 459
⇒ “10.2 Overview - Release Cable”, page 461
⇒ “10.3 Trailer Hitch, Removing and Installing”, page 462
⇒ “10.4 Release Cable, Removing and Installing”, page 468
10.1
Overview - Trailer Hitch
10.1.1
Overview - Trailer Hitch, Sedan
Note
♦
Depending on the version, slight deviations must be considered.
♦
The tightening specifications only apply to factory-installed trailer hitches.
♦
If a different trailer hitch is installed, ask the manufacturer for the tightening specifications.
1 - Trailer Hitch
❑ Swiveling trailer hitch
❑ Removing and instal‐
ling. Refer to
.
2 - Bolt
❑ 20 Nm + 90°
❑ Gas-tight sealing threa‐
ded connections
❑ Quantity: 3
DANGER!
The bolts are actually
sealing threaded con‐
nections and seal off the
vehicle interior from ex‐
haust gas. They must al‐
ways be installed.
3 - Release Cable
❑ With profile
4 - Bolt
❑ 60 Nm + 90°
❑ Replace after removing
❑ Quantity: 2 on each side
5 - Locking Mechanism
6 - Release Lever
❑ Component of the trailer
hitch
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст