Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 257
1 - Rear Door
❑ Removing and instal‐
ling. Refer to
❑ Adjusting. Refer to
2 - Sticker
❑ Quantity: 3
❑ 28 mm diameter
❑ Use commercially avail‐
able duct tape if needed
3 - Sticker
❑ Quantity: 2
❑ 32 mm diameter
❑ Use commercially avail‐
able duct tape if needed
4 - Insulation
❑ Self-adhesive
❑ Installing:
– Cut to size if necessary,
200 mm x 100 mm. Po‐
sition as shown in the il‐
lustration.
– Warm using the Wiring
Harness Repair Set -
Hot Air Blower -
VAS1978/14A- and
then press firmly onto
the outer door panel.
5 - Release Cable
6 - Door Inner Cover
❑ Removing and installing. Refer to
⇒ “2.8 Door Inner Cover, Removing and Installing”, page 170
7 - Outer Door Seal
❑ Secured with clips on the door
❑ Removing and installing. Refer to
⇒ “1.7 Outer Door Seal, Removing and Installing”, page 157
8 - Bracket
❑ Component of the outer door seal
9 - Inner Outer Cover
❑ Removing and installing. Refer to
⇒ “2.17 Outer Cover, Removing and Installing”, page 188
10 - Outer External Cushion
❑ Removing and installing. Refer to
⇒ “2.17 Outer Cover, Removing and Installing”, page 188
11 - Sticker
❑ Quantity: 1
❑ 19 mm diameter
❑ Use commercially available duct tape if needed
12 - Sticker
❑ Quantity: 1
❑ 15 mm diameter
❑ Use commercially available duct tape if needed
13 - Outer Window Shaft Strip
❑ Removing and installing. Refer to
⇒ “2.15 Outer Window Shaft Strip, Removing and Installing”, page 186
14 - Inner Window Shaft Strip
❑ Removing and installing. Refer to
⇒ “2.16 Inner Window Shaft Strip, Removing and Installing”, page 187
.
15 - Sticker
❑ Quantity: 2
❑ 15 mm x 50 mm
❑ Use commercially available duct tape if needed
16 - Window Guide
❑ Removing and installing. Refer to
⇒ “2.14 Window Guide, Removing and Installing”, page 183
.
2.2
Overview - Window Regulator
1 - Front Door
2 - Driver Side Rear Window
Regulator Motor Control Mod‐
ule - J1016- / Front Passenger
Side Rear Window Regulator
Motor Control Module - J1017-
❑ The door control module
and window regulator
motor are one compo‐
nent.
❑ Removing and instal‐
ling. Refer to
.
3 - Hex Nut
❑ 6 Nm
❑ Quantity: 2
4 - Window Regulator
❑ Removing and instal‐
ling. Refer to
.
5 - Bolt
❑ 3 Nm
❑ Quantity: 3 for the win‐
dow regulator motor
with door control mod‐
ule
6 - Window Crank
❑ Removing and instal‐
ling. Refer to
Removing and Installing”, page 168
7 - Bolt
❑ 3 Nm
❑ Quantity: 3 for the window crank mechanism
8 - Window Crank Mechanism
❑ Removing and installing. Refer to
2.3
Overview - Door Handle and Door Lock
Note
The illustration shows the left side. The right side is identical.
1 - Door Lock
❑ Removing and instal‐
ling. Refer to
2 - Bolt
❑ 1.5 Nm
❑ For the locking bracket
in the bracket
3 - Bracket
❑ Removing and instal‐
ling. Refer to
4 - Backing Plate
5 - Cap
❑ Removing and instal‐
ling. Refer to
6 - Door Handle
❑ Removing and instal‐
ling. Refer to
7 - Bolt
❑ 1.5 Nm
❑ Loosening this bolt loos‐
ens the bracket from the
door.
8 - Release Cable
❑ From the door lock -1- to the bracket -3-
9 - Release Cable
❑ From the interior door mechanism to the door lock -1-
❑ With a grommet for the pass through on the cover
10 - Cap
11 - Bolt
❑ 18 Nm
❑ Quantity: 2
2.4
Window Regulator Motor, Removing
and Installing
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Note
The following describes removing and installing the left window regulator motor with door control module. Re‐
moving and installing right window regulator motor with door control module is identical.
Removing
– Remove the rear door trim panel. Refer to ⇒ Body Interior;
Rep. Gr. 70 ; Rear Door Trim Panels; Rear Door Trim Panel,
Removing and Installing .
– Secure the door window with adhesive tape to prevent it from
falling down.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст