Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 217
50 – Body Front
1
Lock Carrier
(Edition 02.2016)
⇒ “1.1 Overview - Lock Carrier”, page 1
⇒ “1.2 Lock Carrier, Removing and Installing”, page 2
⇒ “1.3 Service Position, Implementing and Resetting”,
page 4
⇒ “1.4 Lock Carrier, Servicing”, page 7
1.1
Overview - Lock Carrier
1 - Support
❑ Right
2 - Bolt
❑ 8 Nm
❑ Quantity: 1 on each side
3 - Bolt
❑ 8 Nm
❑ Quantity: 2 on each side
4 - Lock Carrier with Attach‐
ments
❑ Removing and instal‐
ling. Refer to
❑ Service position, imple‐
menting and resetting.
Refer to
.
5 - Support
❑ Left
6 - Air Duct
❑ Left
❑ There are different ver‐
sions. Refer to the Parts
Catalog for the alloca‐
tion.
7 - Lock Carrier Support
8 - Bolt
❑ Quantity: 2
❑ Tightening specification -item 13-
.
9 - Center Guide
10 - Bolt
❑ Quantity: 3
❑ Tightening specification -item 6-
.
11 - Bolt
❑ Quantity: 2 on each side
❑ Tightening specification -item 2-
.
12 - Impact Member
❑ Overview. Refer to
⇒ “1.3 Overview - Impact Member”, page 316
.
13 - Bolt
❑ Quantity: 4 on each side
❑ Tightening specification -item 3-
.
14 - Foam Piece
15 - Air Duct
❑ Right
❑ There are different versions. Refer to the Parts Catalog for the allocation.
1.2
Lock Carrier, Removing and Installing
Special tools and workshop equipment required
♦ Guide Pins - T10093-
♦ Torque Wrench 1331 5-50Nm - VAG1331-
♦ Torque Wrench 1332 40-200Nm - VAG1332-
Note
♦
The lock carrier is a safety-related component. For this reason the lock carrier may only be serviced in the
specified positions.
♦
Replace the lock carrier if it is damaged.
♦
For vehicles with the Distance Regulation Control Module - J428- , the Distance Regulation Control Module
- J428- must be re-aligned during every removal and installation or replacement of the lock carrier.
♦
Notes and work procedures for the Distance Regulation Control Module - J428- . Refer to ⇒ Electrical
Equipment; Rep. Gr. 27 ; Adaptive Cruise Control .
Removing
– Only perform the service position using the Guide Pins -
T10093- . Refer to
⇒ “1.3 Service Position, Implementing and Resetting”,
.
– Disconnect the connector to the lock carrier -1-.
– Together with a second technician, remove the Guide Pins -
T10093- on the left and right longitudinal member. Support the
lock carrier with the attachments -1-. For example on the Scis‐
sor Lift Table - VAS6131B- .
– Remove the bumper carrier and the left and right support. Re‐
fer to
⇒ “1.1 Overview - Lock Carrier”, page 1
– Loosen the radiator from the lock carrier -arrow A-, but do not
remove. Refer to ⇒ Rep. Gr. 19 ; Radiator/Coolant Fan .
– Lift the condenser -3- off of the radiator module -2- -arrow B-
and pivot it slightly out of the lock carrier -arrow C-, but do not
remove.
– Remove the lock carrier -1- between the radiator and con‐
denser upward -D arrows-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст