Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 78
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the footwell cover on the driver side. Refer to ⇒ Body
Interior; Rep. Gr. 68 ; Storage Compartments and Covers;
Driver Side Footwell Cover, Removing and Installing .
– Release the connector -1- and disconnect, to do this grasp
upward behind the pedal bracket.
– To disconnect the connector press the circlip and remove the
connector.
– Release the retainers in direction of -arrows-.
– Remove the Data Bus On Board Diagnostic Interface - J533-
-3- downward from the bracket -2-.
Installing
Install in reverse order of removal.
2.6
Vehicle Electrical System Control Mod‐
ule - J519- Bracket, Removing and In‐
stalling
Removing
– Disconnect the Battery - A- . Refer to
⇒ “1.3 Battery, Disconnecting and Connecting”, page 9
– Remove the instrument panel. Refer to ⇒ Body Interior; Rep.
Gr. 70 ; Instrument Panel; Instrument Panel, Removing and
Installing .
– Cut the cable tie -arrow-.
– Disengage the fuse panel C and press aside. Refer to
⇒ “1.4 Relay and Fuse Carrier Behind Instrument Panel on
Driver Side, Removing and Installing”, page 294
.
– Release and disconnect the connector from the Front Parking
Aid Warning Buzzer - H22- .
– Release and disconnect the connector on the Vehicle Electri‐
cal System Control Module - J519- . Refer to
⇒ “2.4 Vehicle Electrical System Control Module J519 , Re‐
moving and Installing”, page 299
.
– Release and disconnect the connector on the Parking Aid
Control Module - J446- / Parallel Parking Assistance Control
Module - J791- .
– Remove the diagnostic connector, to do this release the lock‐
ing mechanism on the bracket and remove the bracket out‐
ward.
– Remove the bolts -2, 3, and 6-.
– Push the bracket -1- as far as possible out of the central tube
until the alignment pins -4- and -5- are disengaged.
– Cut the cable ties -arrows-.
– Free up the wiring harness on the mount.
– Remove the bracket to the vehicle interior.
Installing
Install in reverse order of removal.
Tightening Specifications
Component
Tightening Specification
Bracket for Vehicle Electrical
System Control Module - J519-
to central tube
4.5 Nm
2.7
Vehicle Electrical System Control Mod‐
ule - J519- Bracket, Replacing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the Vehicle Electrical System Control Module - J519-
bracket. Refer to
⇒ “2.6 Vehicle Electrical System Control Module J519 Brack‐
et, Removing and Installing”, page 301
– Remove the Vehicle Electrical System Control Module -
J519- . Refer to
⇒ “2.4 Vehicle Electrical System Control Module J519 , Re‐
moving and Installing”, page 299
– Remove the Parking Aid Control Module - J446- / Parallel
Parking Assistance Control Module - J791- . Refer to
⇒ “9.2 Parking Aid Control Module J446 , Removing and In‐
– Remove the Front Parking Aid Warning Buzzer - H22- . Refer
to
⇒ “9.3 Front Parking Aid Warning Buzzer H22 , Removing and
.
Installing
Install in reverse order of removal.
2.8
Parking Aid Control Module - J446- /
Parallel Parking Assistance Control
Module - J791- Bracket, Removing and
Installing
Special tools and workshop equipment required
♦ Feeler Gauge
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– If equipped: remove the Parking Aid Control Module - J446- /
Parallel Parking Assistance Control Module - J791- . Refer to
⇒ “9.2 Parking Aid Control Module J446 , Removing and In‐
.
– To loosen the retainers, insert a 0.9 mm feeler gauge -2- be‐
hind the opening -arrow- as illustrated.
– Remove the bracket -1- from below from the Vehicle Electrical
System Control Module - J519- -3- bracket.
Installing
Install in reverse order of removal.
3
Connectors
⇒ “3.1 Wiring Harnesses and Connectors, Repairing”,
3.1
Wiring Harnesses and Connectors, Re‐
pairing
⇒ “3.1.1 Electric Wiring Harnesses and Connectors, Repairing”,
page 304
⇒ “3.1.2 Connector Housings and Connectors, Repairing”,
3.1.1
Electric Wiring Harnesses and Connec‐
tors, Repairing
All instructions and information on this chapter. Refer to ⇒ Elec‐
trical Equipment General Information; Rep. Gr. 97 ; Connectors .
3.1.2
Connector Housings and Connectors,
Repairing
All instructions and information on this chapter. Refer to ⇒ Elec‐
trical Equipment General Information; Rep. Gr. 97 ; Connectors .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст